background image

PERSONAL SAFETY

Stay alert, watch what you are doing and use common sense when 
operating a power tool. Do not use a power tool while you are tired 

or under the influence of drugs, alcohol or medication.

 

A moment 

of inattention while operating power tools may result in serious 

personal injury.

Use personal protective equipment. 

Always wear eye protection. 

Protective equipment such as a dust mask, non-skid safety shoes, 

hard hat, or hearing protection used for appropriate conditions will 

reduce personal injuries.

Prevent unintentional starting. Ensure the switch is in the Off 

position before connecting to power source and/or battery pack, 

picking up or carrying the tool. 

Carrying power tools with your 

finger on the switch or energizing power tools that have the switch 

on invites accidents. 

Remove any adjusting key or wrench before turning the power tool 

on.

 

A wrench or a key left attached to a rotating part of the power 

tool may result in personal injury.

Do not overreach. Keep proper footing and balance at all times.

 

This enables better control of the power tool in unexpected 

situations.

Dress properly. Do not wear loose clothing or jewelry. Keep your 
hair, clothing and gloves away from moving parts. 

Loose clothes, 

jewelry or long hair can be caught in moving parts.

If devices are provided for the connection of dust-extraction and 
dust-collection facilities, ensure these are connected and properly 
used. 

Dust-collection can reduce dust-related hazards.

SAVE THESE INSTRUCTIONS FOR REFERENCE.

POWER TOOL USE AND CARE

Do not force the power tool. Use the correct power tool for your 

job.

 

The correct power tool will do the job better and safer at the 

rate for which it was designed.

Do not use the power tool if the switch does not turn it On and 
Off.

 

Any power tool that cannot be controlled with the switch is 

dangerous and must be repaired.

Disconnect the plug from the power source and/or the battery pack 
from the power tool before making any adjustments, changing 

accessories or storing power tools. 

Such preventive safety measures 

reduce the risk of starting the power tool accidentally.

Store idle power tools out of the reach of children and do not allow 
people unfamiliar with the power tool or these instructions to 
operate the power tool.

 

Power tools are dangerous in the hands of 

untrained users.

Maintain power tools. Check for misalignment or binding of 
moving parts, breakage of parts and any other conditions that 

may affect the power tool’s operation. If damaged, have the power 

tool repaired before use.

 

Many accidents are caused by poorly 

maintained power tools.

Keep cutting tools sharp and clean.

 

Properly maintained cutting 

tools with sharp cutting edges are less likely to bind and are easier 

to control.

Use the power tool, accessories and tool bits etc. in accordance 

with these instructions, taking into account the working conditions 

and the work to be performed. 

Use of the power tool for operations 

different from those intended could result in a hazardous situation.

Hold power tools by insulated gripping surfaces when performing 

an operation where the cutting tool may contact hidden wiring or 
its own cord.

 

Contact with a “live” wire will make exposed metal 

parts of the tool “live” and shock the operator.

SAVE THESE INSTRUCTIONS FOR REFERENCE.

8

9

model no. 055-6701-6     contact us 1-800-689-9928

I

  

SAFETY GUIDELINES

  

SAFETY GUIDELINES

Содержание Maximumu 055-6701-6


















Отзывы: