MasterCraft debrismaster Скачать руководство пользователя страница 5

S

WEEPER

C

ONTROLS

Control Panel

Side Brush Control Lever:

Push lever down to turn 

ON

the side

brush. Push lever up to turn 

OFF

the

side brush.

Key Switch:

Starts and turns off all the sweeper’s
functions including the Main Brush.

Fan Indicator Light

Indicates that the fan is in use.

Push Botton Suction Impeller:

Activates the suction Impeller.

Traction Lever:

Squeeze this lever to start the sweeper
moving.

Airflow Adjustment Knob:

Opens and closes the air valve when
regulating the airflow. 

(36” Sweeper Only)

Voltage Indicator Light

Indicates the sweeper’s power levels.

Battery Sweepers Only

Battery Charger Socket:

Plug for battery charger.

Battery Charge Indicator Lights:

Green

: Battery is charged.

Yellow

: Battery is running down,

recharge as soon as possible.

Red: DO NOT

operate, batteries 

must be recharged.

1)

When picking up light but bulky

debris (sheets of paper, leaves, etc.)
raise the front part of the sweeper by
pressing down the handle so that the
sweeper can tackle the rubbish.

2) DO NOT

use the sweeper to pickup

wires, ropes, and straps or to soak up
any liquids.

3)

Operate the Filter Shaker at the end

of your work (see pg 6).

4)

Check to make sure the Main Brush

is correctly adjusted (see pg 7).

To Start Operating The
Sweeper:

1) 

Check to make sure that the side

brush is 

OFF

.

2)

Turn the Key Switch to 

ON

3) 

Battery units have a 10 seconds delay

while the battery voltage level is checked.
If the voltage is at the correct charge
level the Main Brush will turn 

ON

.

4)

Push the Side Brush Control Lever

down to lower and turn 

ON

the side

brush.

5)

Squeeze the Traction Lever (on right)

to move the sweeper forward and start
cleaning.

6)

Squeeze Debris Flap Lever (on left)

for removal of large debris.

O

PERATING

P

ROCEDURES

DO NOT leave sweeper unattended when it is running or on 

sloping surfaces,there is NO brake to keep it from rolling.

Before leaving the sweeper turn it OFF and remove the key.

C

AUTION

:

Airflow Adjustment
Knob

Traction Lever

Side Brush Control Lever

Follow these instructions to obtain the best cleaning results from the sweeper and
keep damage to a minimum.

P

AGE

5

Содержание debrismaster













Отзывы: