MasterCraft debrismaster Скачать руководство пользователя страница 12

T

ROUBLE

S

HOOTING

G

UIDE

Address:

777 South Street

P.O. Box 2310

Newburgh, N Y 12550-0606

TEL: 

(800) 835-7812 
(845) 565-8850

FAX

(800) 752-6883
(845) 565-9392

URL:

www.mastercraftusa.com 

E-mail:

[email protected]

Always turn the sweeper OFF before servicing.

PROBLEM: Main brush not working.

CAUSE:

SOLUTION:

1) 

Belt is broken.

1) 

Replace belt.

2)

Motor burnt out.

2) 

Replace motor.

3)

Wire is detached.

3)

Check and reattach.

4)

Circuit board damaged.

4)

Check and replace.

PROBLEM: Side brush not working.

CAUSE: SOLUTION:

1) 

Belt is broken.

1) 

Replace belt.

PROBLEM: Battery will not stay charged.

CAUSE: SOLUTION:

1) 

Liquid is insufficient.

1) 

Add liquid.

2) 

Battery terminal is loose.

2) 

Tighten terminal.

PROBLEM: Dust blowing from fan.

CAUSE: SOLUTION:

1) 

Filter is damaged.

1)

Replace filter.

2)

Filter not correctly installed.

2)

Install correctly.

3) 

Gasket is worn.

3) 

Replace gasket.

PROBLEM: Brushes wear prematurely.

1) 

Brushes are to low.

1)

Adjust brushes.

PROBLEM: Dust forms during operation.

CAUSE: SOLUTION:

1) 

Flaps are worn.

1)

Replace flaps.

2) 

Filter is clogged.

2)

Clean filter.

PROBLEM: Motor does not work.

CAUSE: SOLUTION:

1) 

Motor is damaged or burnt out.

1)

Replace motor.

2)

Wire is disconnected.

2)

Check and reconnect wire.

3)

Impeller is clogged or blocked

3)

Clean impeller. 

PROBLEM: Sweeper will not start.

CAUSE: SOLUTION:

1) 

Battery terminals are disconnected.

1) 

Check and reconnect terminals.

2)

Battery need to be recharged.

2)

Charge battery.

3)

Fuse is blown.

3)

Replace fuse.

4)

Gas tank empty.

3)

Refill tank.

Repairs should only be performed by an authorized service center.

W

ARNING

:

P

AGE

12

C

AUTION

:

28” & 36” Sweeper - PN 447404 -Printed in USA  08/22/07

Содержание debrismaster













Отзывы: