MasterCraft 55-6847-0 Скачать руководство пользователя страница 20

Страница: 20 / 23

TROUBLESHOOTING

SUGGESTED CORRECTIVE
ACTION

PROBLEM

PROBLEM CAUSE

Motor brake overheated
from use of defective or
wrong size blade or rapid
ON/OFF cycling.

Use a recommended blade.

ake does not stop blade

within 6 seconds

Arbour bolt loose.

Retighten.

Electric Brake has failed

Take saw for servicing

Motor does not start

Saw not plugged in

Check that all electric
connections are secure

Fuse.

Check time delay fuse or
circuit breaker.

Mitre table unlocked.

Use mitre table locking lever
“See ADJUSTMENT section.”

Angle of cut is inaccurate

Too much sawdust under
table.

Vacuum or blow out dust.
WEAREYE PROTECTION!

Parts failure.

Contact CTC Service Centre.

Pivot spring not replaced
properly after service.

Contact CTC Service Centre.

Cutting arm cannot fully raise,
or blade guard cannot fully
close

Clean and lubricate moving
parts.

Sawdust build-up.

Check, adjust, and properly
set the saw-head locking pin

Saw-head locking pin is not
properly set or adjusted

Improper operation.

“See OPERATION section.”

Dull blade.

Replace or sharpen blade.

Blade binds, jams, or burns
wood

Improper blade.

Replace blade.

Warped blade.

Replace blade.

Saw blade damaged.

Replace blade.

Saw vibrates or shakes

Saw blade loosened.

Tighten arbour bolt.

Work piece is not properly
supported

Properly support or clamp
work piece

Saw not properly fastened

Properly support or clamp
work piece

Contact CTC Service Centre when the problems remain unsolved after the checks above.

Repair Parts

INCLUDES:

•

1 pc of 40T carbide tip blades

•

1 pc of hold down clamp

•

1 pc of dust collection bag

•

1 pc wrench

•

1 pc vacuum adapter

Содержание 55-6847-0
























Результаты поиска

Содержание 55-6847-0

Отзывы:

Бренды по названию

Популярные бренды

MasterCraft 55-6847-0, Руководство по эксплуатации

Результаты поиска

Содержание 55-6847-0

Отзывы:

Бренды по названию

Популярные бренды