MasterCraft 55-6847-0 Скачать руководство пользователя страница 19 | Manualshive

Страница: 19 / 23

background image

MAINTENANCE

Before cleaning or performing any maintenance, make sure that the Compound Mitre Saw has been
disconnected from the power supply. Keep all ventilation openings clean. Avoid using solvents when
cleaning plastic parts. Most plastics are susceptible to damage from various types of commercial
solvents and may be damaged by their use. Use a clean cloth to remove dirt, oil and grease.

WARNING:

Do not allow improper materials, such as brake fluids, gasoline, petroleum-based

products, penetrating oil, etc., to come in contact with plastic parts as improper materials contain
chemicals that can damage, weaken or destroy plastic.

WARNING:

To ensure safety and reliability, all repairs should be performed by a qualified

service technician.

19

«
...
17
18
19
20
21
...
»

Содержание 55-6847-0
























Отзывы:

Нет отзывов

Похожие инструкции для 55-6847-0

Бренд: Oliver Страницы: 52

Бренд: Ferm Страницы: 108

Бренд: BGU Страницы: 24

Бренд: MASTERPAC Страницы: 24

Бренд: Raider Страницы: 92

Бренд: Jet Страницы: 32

Бренд: Parkside Страницы: 92

Бренд: SWS Power Tools Страницы: 22

Бренд: Silverline Страницы: 40

Бренд: Clarke Страницы: 16

Бренд: Clarke Страницы: 16

Бренд: Clarke Страницы: 16

Бренд: Clarke Страницы: 28

Бренд: GMC Страницы: 11

Бренд: Rothenberger Страницы: 33

Бренд: Charnwood Страницы: 16

Бренд: PrimeCables Страницы: 26

Бренд: QEP Страницы: 14

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды