MasterCraft 54-2903-2 Скачать руководство пользователя страница 9 | Manualshive

Страница: 9 / 37

MasterCraft 54-2903-2 Скачать руководство пользователя страница 9

9

Do NOT charge Ni-Cd or Ni-MH batteries
when the temperature of the work area or
the battery is above 55° C (131° F).
Do NOT charge Li-ion batteries when the
work area or the battery temperature is at
or below 0°C (32° F) or above 45° C
(113° F).

Unplug the charger when not in use and
before cleaning or maintenance.

BATTERY PACK RECYCLING

To preserve our natural resources, please
recycle or dispose of batteries properly.

The batteries accompanying this tool may
contain chemicals and metals that are
harmful to the environment. Never dispose
of re-chargeable batteries in your normal
household garbage or in landfill sites as
they will add to the pollution of the
environment.

Please return all defective rechargeable
battery packs to your local Canadian
Tire™ store for recycling. If you do not
have a Canadian Tire™ store in your area,
please call 1-800-822-8837 for the location
of your nearest RBRC battery recycling
location.

Consult your local waste authority for
information regarding additional available
recycling and disposal options.

BATTERY & CHARGER SAFETY

NOTE:

See Pages 32 & 33 for

detailed information concerning
preparation for recycling battery packs
and exercising the Ni-Cd battery pack
for peak performance.

«
...
7
8
9
10
11
...
»

Содержание 54-2903-2






































Отзывы:

Нет отзывов