MasterCraft 54-2903-2 Скачать руководство пользователя страница 5 | Manualshive

Страница: 5 / 37

MasterCraft 54-2903-2 Скачать руководство пользователя страница 5

5

GENERAL SAFETY RULES

WARNING:

Read and understand

all instructions.

Failure to follow all

instructions listed below may result in
electric shock, fire and/or serious personal
injury.

WORK AREA

Keep your work area clean and well lit.
Cluttered benches and dark areas invite
accidents.

Do not operate power tools in potentially
explosive environments, such as in the
presence of flammable liquids, gas or dust.
Power tools create sparks that may ignite
dust or fumes.

Keep bystanders, children and visitors
away while operating the tool. Distractions
can cause the operator to lose control.

ELECTRICAL SAFETY

Double insulated tools are equipped with a
polarized plug (one blade is wider than the
other).

This plug will only fit into a

polarized plug one way.

If the plug does not fit into the outlet
properly, reverse the plug.

If it still does not

fit, contact a qualified electrician to install a
polarized outlet. Do not alter the plug in
any way.

Double insulation eliminates the

need for the three-pronged grounded
power cord and grounded power supply
system.

Avoid contact between the operator's body
and grounded surfaces such as pipes,
radiators, ranges, and refrigerators. There
is an increased risk of electric shock if the
operator's body is grounded.

Do not expose power tools to rain or wet
conditions. Water entering the power tool
will increase the risk of electric shock.

Do not abuse the cord. Do not use the
power cord to carry the tool or to pull the
plug out of the outlet. Keep the power cord
away from heat, oil, sharp edges, and
moving parts. Replace a damaged power
cord immediately. A damaged power cord
increases the risk of electric shock.

When operating a power tool outdoors,
use an outdoor-rated extension cord type
“W-A” or “W”. These cords are rated for
outdoor use and they reduce the risk of
electric shock.

PERSONAL SAFETY

Stay alert, be aware of the surroundings,
and use common sense when operating a
power tool. Do not use a power tool while
tired or under the influence of drugs,
alcohol, or medication. A moment of
inattention while operating a power tool
may result in serious personal injury.

Dress properly.

Do not wear loose clothing

or jewellery.

Contain long hair. Keep hair, clothing, and
gloves away from moving parts. Loose
clothing, jewellery, or long hair can get
caught in moving parts.

!

POWER TOOL SAFETY

«
...
3
4
5
6
7
...
»

Содержание 54-2903-2






































Отзывы:

Нет отзывов