MasterCraft 054-6821-2 Скачать руководство пользователя

Страница: 7 / 28

headline bars

continuation tabs

notes

warnings

headline bars

continuation tabs

notes

warnings

headline bars

continuation tabs

notes

warnings

SAFETY GUIDELINES

•

Do not let familiarity gained from frequent use of tools allow you to become

complacent and ignore tool safety principles.

A careless action can cause severe injury

within a fraction of a second.

POWER TOOL USE AND CARE

•

Do not force the power tool. Use the correct power tool for your application.

The correct

power tool will do the job better and safer at the rate for which it was designed.

•

Do not use the power tool if the switch does not turn it on and off.

Any power tool that

cannot be controlled with the switch is dangerous and must be repaired.

•

Disconnect the plug from the power source and/or remove the battery pack,

if detachable, from the power tool before making any adjustments, changing

accessories, or storing power tools.

Such preventive safety measures reduce the risk of

starting the power tool accidentally.

•

Store idle power tools out of the reach of children and do not allow persons unfamiliar

with the power tool or these instructions to operate the power tool.

Power tools are

dangerous in the hands of untrained users.

•

Maintain power tools and accessories. Check for misalignment or binding of moving

parts, breakage of parts and any other condition that may affect the power tool’s

operation. If damaged, have the power tool repaired before use.

Many accidents are

caused by poorly maintained power tools.

•

Keep cutting tools sharp and clean.

Properly maintained cutting tools with sharp cutting

edges are less likely to bind and are easier to control.

•

Use the power tool, accessories and tool bits etc. in accordance with these

instructions, taking into account the working conditions and the work to be

performed.

Use of the power tool for operations different from those intended could result in a

hazardous situation.

•

Keep handles and grasping surfaces dry, clean and free from oil and grease.

Slippery

handles and grasping surfaces do not allow for safe handling and control of the tool in
unexpected situations.

SERVICE

•

Have your power tool serviced by a qualified repair person using only identical

replacement parts.

This will ensure that the safety of the power tool is maintained.

SAFETY INSTRUCTIONS FOR ROUTERS

•

Hold the power tool by insulated gripping surfaces only, because the cutter may

contact its own cord.

Cutting a “live” wire may make exposed metal parts of the power tool

“live” and could give the operator an electric shock.

•

Use clamps or another practical way to secure and support the workpiece to a stable

platform.

Holding the work by your hand or against the body leaves it unstable and may lead to

loss of control.

Содержание 054-6821-2





























Результаты поиска

Содержание 054-6821-2

Отзывы:

Похожие инструкции для 054-6821-2

Бренды по названию

Популярные бренды

MasterCraft 054-6821-2, Инструкция по эксплуатации

Результаты поиска

Содержание 054-6821-2

Отзывы:

Похожие инструкции для 054-6821-2

Бренды по названию

Популярные бренды