background image

 

12 

 
 
 
INSTALLING THE BATTERY PACK IN THE 
IMPACT DRIVER 

 
1. 

Remove the discharged battery pack (1) 
from the tool by pressing the battery 
release button (2) on the rear of the battery 
downward (Fig. 3) and pulling the battery 
pack out of the tool handle (3) (Fig. 4). 

 

2. 

Insert the fully charged battery pack into 
the matching slots in the rear of the tool 
handle where the discharged battery pack 
has been removed. 

NOTE:

 The battery release button will 

"click" into place when the battery pack is 
fully installed.

 

 

      

WARNING:

 Do not immerse battery 

pack in water. Sudden cooling could cause a 
hot battery to explode or leak.

 

 
 
 
 
 
 
 
 

 

 
ON-BOARD SCREWDRIVER BIT STORAGE 

 
Convenient on-board screwdriver bit storage (1) 
is provided on the drill/driver handle base (Fig. 
5). 

 
 
 
INSTALLING DRIVER BITS

 

 
      

WARNING:

 Use only screwdriver bits, 

sockets and accessories that are designed 
for use with an impact driver.

 Do not use 

chrome plated sockets and accessories. 
Chrome plated sockets and accessories are 
designed for hand use only and MUST NOT be 
used with an impact driver. They may shatter 
and possibly cause serious injury. 
 
      

WARNING:

 

Always remove the battery 

from the tool before changing any sockets, bits 
or accessories. You may injure your hand if the 
tool is started accidentally. 
 
1. 

To install a screwdriver bit, pull outward on 
the hex drive sleeve (1) (Fig. 6). While 
holding the hex drive sleeve out, insert the 
bit (2) fully into the hex drive and then 
release the outer sleeve. 
 

2. 

When the hex drive sleeve is released, pull 
outward on the bit to ensure the retaining 
ball inside the hex drive is engaged with 
the groove in the bit (3) to prevent the bit 
from sliding out of the hex drive. 

 
3. 

To remove the bit, pull outward on the hex 
drive sleeve and pull the bit out of the hex 
drive. 

 
      

WARNING:

 

Never use a screwdriver bit or 

nut driver that does NOT have the locking 
groove. These accessories will not be 
adequately held in the hex drive and could come 
loose and possibly injure the operator. 
 

ASSEMBLY AND OPERATING 

Fig. 3 

 

Fig. 4 

 

Fig. 5 

 

 

Fig. 6 

Содержание 054-3167-8























Отзывы: