background image

 

9

To initiate a Manual Defrost, press and hold the MAN DEF key for 3 seconds. 
 
There are two levels of programming in the ERC 2. The first level of security will enable the user to 
set two parameters: Time-of-day (

CLoC

) and Set point temperature (

SEt

). The other level allows 

access to the other parameters. 
 
 
Three buttons are used for the programming: SET, UP and DOWN 
 
 

Fig. 4 – Display Lay-out 

  
To change time-of-day and set point temperature (First Level) follows these steps: 
 

Step 1 

 

Press and hold set for 5 seconds. The display will show 

CLoC

 

Step 2 

 

Press SET again to change the time-of-day 

Step 3 

 or 

 

Press UP or DOWN until the correct time-of-day is displayed 

Step 4 

 

Press SET to accept the new time 

Step 5 

 

Press DOWN to go to the next parameter – Set point 
Temperature - (cut out) 

Step 6 

 

Press SET to change the set point temperature 

Step 7 

 or 

 

Press UP or DOWN to go to the desired set point. The range is  
– 40 to 60

°

F or –40 to 16

°

C  

Step 8 

 

Press SET to accept the change 

Step 9 

 

Press DOWN to exit the first level of programming 

 
Note 1: During programming, if no button is pushed during 30 seconds, the control will go 
back to the normal operating mode. This is valid for both programming levels. 
 
Note 2: When changing the time, press and hold the MAN DEF button for 3 seconds to 
change the AM/PM mode. 
 
Note 3: Master-Bilt’s Set point Temperature (

Set)

 is set at a recommended –10

°

F at the 

factory for low temperature(LT) and +35

o

F for medium temperature(MT) application.  

  

 

Note 4: If demand defrost (

ddEF

) is used, the minimum number of defrost is 1 per 24 hours. 

 
 
 
 
 

Содержание TAF-27 ERC2 s



















Отзывы: