42
9. Update
Der DiMAX Navigator kann über die Busver
-
bindung via Digitalzentrale oder PC Modul mit
der neuesten Firmware upgedated werden.
•
Für ein Softwareupdate an der Zentrale sollte der
DiMAX Navigator alleine angeschlossen sein.
Detaillierte Anweisung zur Durchführung des
Updates finden Sie in der DIMAX Anleitung.
•
Zum Update mit dem PC-Modul muss die
rechte ‚Stop‘ Taste beim Einstecken des Kabels
gedrückt werden (Der Navigator startet den
Updatemodus).
10. Tips & Tricks für Servicezwecke
Die Softwareversion und die Seriennummer des
Navigators werden beim Start kurz angezeigt.
(1. Zeile links = Serien Nr., rechts = Version)
Mit gedrückter F-Taste bleibt die Anzeige länger.
Im Funkbetrieb wird die Version beim
Ausschalten angezeigt. Rechte ‚Stop‘ Tas-
te beim Einschalten festhalten startet das
Softwareupdate direkt. Linke ‚Stop‘ Taste beim
Einschalten festhalten lädt Lokadresse 0 falls
der Navigator nicht mehr einwandfrei startet.
11. Funkeinbau oder -umbau
Ein kabelbetriebener Navigator kann mit einem
Funksender (#8131901) ausgestattet werden.
Beim nachträglichen Einbau beachten Sie bitte
beiliegende Einbauhinweise! Für den Funk-
betrieb ist ein Softwarestand von mindestens
Version 2.1 notwendig. Führen Sie dafür bitte
ein entsprechendes Softwareupdate durch.
12. Technische Daten: Kabelbetrieb
•
Betrieb an folgenden Zentralen
DiMAX 800Z, 1200Z, 1210Z, MZS III, PIKO G
•
Spannungsversorgung
12...24V DCC
•
Maximale Stromaufnahme
80mA
•
Temperaturbereich
-20 .. 50° C
•
Abmessungen (L x B x H)
188 x 78 x 36 mm
12.1 Technische Daten: Funkbetrieb
•
Funkbetrieb über folgende Empfänger
8131001, 8133101, 8132001, 8130101
9. Update
The DiMAX Navigator is a state-of-the-art
handheld. It may be updated with the lat-
est firmware version directly via the bus.
• For a software update via Central Station con
-
nect only the Navigator and no other bus device.
Please check the Central Station manual for
detailed information how to perform the update.
•
To perform the on the PC Module the right
“STOP”-key has to be pushed when connecting
the Navigator.
10. Tips & Tricks for Service purposes
The Software version and the serial number is
shown when the Navigator starts.
(1. row left = Serial Number, right = Version).
Holding the F-key will show the initial screen
for a longer time. In R/C mode the version
is shown when the Navigator is shut down.
Holding the right “STOP”-key while starting
the Navigator will force to start the update
procedure. Holding the left “STOP”-key while
starting the Navigator will load the locomotive
address 0 to reset the formerly used settings.
11.
Retrofit R/C installation
The DiMAX Navigator may be retrofit
-
ted with a R/C transmitter (#8131901).
Please refer to the installation manual for
retrofit installation. A firmware version
2.1 or later is required for R/C operation.
Please update the Navigator if required.
12.
Technical Specifications: Cable operation
•
Operation with the following Central Stations
DiMAX 800Z, 1200Z, 1210Z, MTS III, PIKO G
•
Operating Voltage
12...24V DCC
•
Maximum Current
80mA
•
Temperature range
-20°C to +45°C / -4°F to +113°F
•
Measurements (L x W x H)
188 x 78 x 36 mm
12.1
Technical Specifications: R/C operation
•
Operation with the following R/C Receivers
8131001, 133101, 8132001, 8130101
Содержание DiMAX Navigator
Страница 1: ...DiMAX Navigator ...