Masport MADRID Скачать руководство пользователя страница 15

Masport Inbuilt Gas Fireplace

- 15 -

thermodisc  is  fitted,  it  is  not  necessary  to  operate  the
switch on the fascia. It  can  be  kept  permanently  on  at
the  desired  speed  setting.  The  fascia  switch  overrides
the thermodisc if it is set in the central “off” position.

NORMAL OPERATING SOUNDS OF
GAS APPLIANCES

It is possible that you will hear some sounds from your
gas appliance. This is perfectly normal  due  to  the  fact
that  there  are  various  gauges  and  types  of  steel  used
within  your  appliance.  Listed  below  are  some
examples,
all  are  normal  operating  sounds  and  these  should
not be considered as defects in your appliance.

Fan:
Masport gas appliances use high tech blowers to push
heated  air  further  into  the  room.  It  is  not  unusual  for
the  fan  to  make  a  "whirring"  sound  when  ON.  This
sound  will  increase  or  decrease  in  volume  depending
on the speed setting of your fan.

Burner Tray:
The burner tray is  positioned  directly  under  the  burner
and  logs  and  is  made  of  a  different  gauge  material
from  the  rest  of  the  firebox  and  body.  Therefore,  the
varying thicknesses of steel will expand and contract at
slightly  different  rates,  which  can  cause  "ticking"  and
"cracking"  sounds.  You  should  also  be  aware  that  as
there  are  temperature  changes  within  the  unit  these
sounds  would  likely  re-occur,  again,  this  is  normal  for
steel fireboxes.

Pilot Flame (Piccolo Only):
While  the  pilot  flame  is  on  it  can  make  a  very  slight
"whisper" sound.

Gas Control Valve:
As  the  gas  control  valve  turns  ON  and  OFF,  a  dull
clicking sound may be audible, this is normal operation
of a gas regulator or valve.

Unit Body/Firebox:
Different  types  and  thicknesses  of  steel  will  expand
and  contract  at  different  rates  resulting  in  some
"cracking" and "ticking" sounds being heard throughout
the cycling process.

GENERAL MAINTENANCE
INSTRUCTIONS

1) Keep the burner and control compartment clean by

brushing  and  vacuuming  at  least  once  a  year.
Always turn the gas valve to OFF before cleaning.
When  cleaning  the  logs,  use  a  clean  soft
paintbrush,  as  the  logs  are  fragile  and  easily
damaged.

2) Clean  the  appliance,  glass  and  louvres  with  a

damp  cloth  only  when  it  is  cold.  Never  use  an
abrasive  cleaner.  The  gold  louvres  will  be
scratched if abrasives are used to clean them.
The heater is finished in a heat resistant paint and
should  only  be  refinished  with  heat  resistant  paint
(not with wall paint).

3) Keep  the  area  near  the  appliance  clear  and  free

from  combustible  materials,  petrol  and  other
flammable vapours and liquids.

WARNING:  CHILDREN AND ADULTS SHOULD
BE  ALERTED  TO  THE  HAZARDS  OF  HIGH
SURFACE  TEMPERATURE  AND  SHOULD
STAY AWAY TO AVOID BURNS OR CLOTHING
IGNITION.    YOUNG  CHILDREN  SHOULD  BE
CAREFULLY  SUPERVISED  WHEN  THEY  ARE
IN THE SAME ROOM AS THE APPLIANCE.

CAUTION:  ANY SAFETY SCREEN OR GUARD
REMOVED  FOR  SERVICING  AN  APPLIANCE
MUST  BE  REPLACED  PRIOR  TO  OPERATING
THE APPLIANCE. (Australia only)

CLOTHING 

OR 

OTHER 

FLAMMABLE

MATERIAL  SHOULD  NOT  BE  PLACED  ON  OR
NEAR THE APPLIANCE.

4)  Periodically  check  the  pilot  flames  (Piccolo  only),

there  should  be  three  strong  flames  (approx.  19
mm  long)  -  1  flame  to  the  rear  burner,  1  to  the
ignition electrode and 1 to the thermocouple.

If you have an incorrect flame pattern, contact your
Masport dealer.

SERVICING INSTRUCTIONS

(Routine maintenance schedule)

Servicing must be carried out only by authorised
personnel.

Your  Masport  heater  must  be  checked  yearly  by  an
authorised  Technician.  This  periodic  maintenance
should cover the following points:-

1) Keep the burner and control compartment and any

air entry points  clean  by  brushing  and  vacuuming.
Always turn the gas valve to OFF before cleaning.
When  cleaning  the  logs,  use  a  clean  soft
paintbrush,  as  the  logs  are  fragile  and  easily
damaged.

2) Make  a  periodic  check  of  burner  for  proper  log

position  and  condition.  Visually  check  the  flame
pattern of the burner  periodically,  making  sure  the
flames are steady, not lifting or floating.

3) The  appliance  and  flue  system  must  be  inspected

before  use  and  thereafter  annually  to  ensure  that
the  flow  of  combustion  and  ventilation  air  is  not

Содержание MADRID





















Отзывы: