Maschio ORSO RAPIDO 3000, Использование и обслуживание

Страница: 70 / 126

cod. F07011388
USE AND MAINTENANCE
ENGLISH
70 - EN
4.4 TRANSPORT
If it becomes necessary to transport the machine for a long distance, it can be loaded onto a railway wagon or a truck. For this purpose,
consult «Technical Data» for weight and speci
fi
c dimensions. The latter are very useful to check the possibility of driving along all types
of roads.
The machine is generally supplied in a horizontal position with no packing material.
It is therefore necessary to use a system of hoisting with a crane and cables, or chains of adequate capacity, hooking onto the machine
at the hoisting points marked with the «hook» symbol (
fi
g.6 ).
CAUTION
Before proceeding to the hoisting op- erations, make sure that any any mo- bile elements of the machine are blocked. Make
sure to use a crane with an adequate hoisting capacity to lift the machine. Hoist the machine with extreme caution and transfer
it slowly, without jerks or abrupt movements.
DANGER
The operations of hoisting and trans- port can be very dangerous if not carried out with the maximum caution; persons not
directly involved should be moved away. Clean, evacuate the area and delimit the transfer zone. Check the state, condition
and suit- ability of the means at disposition. Do not touch suspended loads, keep- ing them at a safe distance.
It most be further ascertained that the operational area is free of obstacles and that there is suf
fi
cient «escape space», mea-
ning an area which is free and secure into which one could move rapidly in case a load should fall. The surface on which the
machine is to be loaded must be horizontal in or- der to prevent possible shifting.
Once the machine is positioned on the vehicle, make sure that it remains blocked in its position. Fasten the machine on the platform of
the vehicle by means of cables suitable for the mass which must be blocked (see «Technical Data» for the weight).
The cables must be
fi
rmly fastened to the machine and pulled taut to the anchorage point on the platform. Once transport has been
carried out and before freeing the machine from all its fastenings, make sure that its state and position are such as not to constitute
danger. Remove the cables and proceed to unloading with the same means and methods used for loading.
Transit and transporting on the public highways
When driving on the public roads,
fi
t on the rear re
fl
ector triangles, side lights and
fl
ashing beacon and always make sure that you
comply with the Highway Code and any other applicable regulations.
Make sure that the machine dimensions during transfer phases allow for safe transport when travelling in subways, along narrow roads,
near electrical lines, etc..
ATTENTION
Before driving on to the public roads with the machine hitched to the tractor, make sure that the devices listed above and/or
the slow vehicle signal and/or the projecting load signal op- erate correctly. These indicators must be af
fi
xed to the rear of
the implement in a position where they can be clearly seen by any other vehicle that drives up behind.
The tractor used for transporting the equipment must have the powers shown in the Technical Data table; if necessary, redistribute the
total weights with the addition of ballasts to return balance and stability to the whole assembly.
For displacements beyond the work area, the equipment must be placed in the transportation position:
- Where provided for, make all the moving parts come within the transport width, locking them with the safety devices (toolbars, row
marker arms, row marker discs, etc.).
- Any transport accessories must be provided with suitable signs and guards.
Upon request the Manufacturer will supply supports and tables for signaling of dimensions.
4.5 HYDRAULIC SYSTEM
Once these preliminary operations have been accomplished (coupling of 3-point hitch to the tractor and cardan shaft engagement),
connect the hydraulic system (
fi
g.56) to the tractor. This will enable the harrow to accomplish its various movements, i.e.:
- The pipes of the two hydraulic cylinders «A» to regulate the rear rollers that establish the work depth.
NOTE: The cylinders «B» that operate the closing clips are controlled in sequence with the cylinders that control the units.
A speci
fi
c control is therefore not required.
Recognizing the pipe functions
All hydraulic pipes on the machine have recognition stickers as indicated in
fi
g.56
1
: Rear roller lowering.
2
: Rear roller lifting.
NOTE: The two cylinders «A» (
fi
g.56) are equipped with a block valve which acts if a pipe breaks.
WARNING
Check the hydraulic pipes frequently and replace them whenever they show signs of wear or if small cracks form in the rubber.