manualshive.com logo in svg

Marvair ComPac I AVP24, Руководство по эксплуатации продукта

Поделиться
Скачать
Marvair ComPac I AVP24 Скачать руководство пользователя страница 24

 

ComPac 6/09-18

2.8  e

leCTriCal

 C

onneCTions

Important

All electrical work must meet the requirements of local codes and ordinances. 

 Work should be 

done 

only

 by qualified persons.

The ComPac

®

 units may incorporate an internal crankcase heater for compressor protection.   

The 

crankcase heater must be energized for at least 24 hours prior to starting the compressor.

Scroll compressors, like several other types of compressors, will only compress in one rotational direction. 

The direction of rotation is not an issue with single-phase compressors  since they will always start and 

run in the proper direction. However, three phase compressors will rotate in either direction depending 

upon phasing of power. Since there is a 50-50 chance of connecting power in such a way as to cause 

rotation in the reverse direction, it is imperative to confirm that the compressor is rotating in the proper 

direction at the initial field start-up of the system. Verification of proper rotation is made by observing 

that the suction pressure drops and the discharge pressure rises when the compressor is energized. An 

alternate method of verification for self contained system with small critical refrigerant charges, where 

the installation of gauges may be objectionable, can be made by monitoring the temperature of the 

refrigerant lines at the compressor. The temperature should rise on the discharge line while the suction 

line temperature decreases. Reverse rotation also results in a substantially reduced current draw when 

compared to tabulated values.

Marvair units have either a reciprocating or scroll compressor. A reciprocation compressor is standard 

on the AVP24, 30 & 36 units. However, a scroll compressor is an option on these ComPac

®

 I and 

ComPac

®

 II air conditioners. Units with scroll compressors have a "U" in the model number. The scroll 

compressor is standard on all AVP42, 48, 60 & 72 units. 

There is no negative impact on durability caused by operating three phase compressors in the reversed 

direction for a short duration of time, usually defined as less than one hour. However, after several 

minutes of operation the compressor's internal protector will trip. The compressor will then cycle on 

the protector until the phasing is corrected. Reverse operation for longer than one hour may have a 

negative impact on the bearings.

  

High Voltage Wiring - (Single Units)

The power supply should have the proper voltage, phase, and ampacity for the selected model. 

1.  Size the incoming power supply lines according to Code requirements.  Run the power conductors 

through the knockouts on the wall side of the unit, or to those adjacent to the electrical control box.  

Use appropriate conduit and strain reliefs.   

2.  Connect the wires to the input side of the internal breaker or terminal block (L1 & L2 for single-

phase units; L1, L2, & L3 for three-phase models). 

3.  Install the ground wire on the ground lug.

 WARNING 

ELECTRICAL SHOCK HAZARD

Failure to follow safety warnings exactly could result in serious injury, death, and/or 

property damage.
Turn off electrical power at fuse box or service panel BEFORE making any electrical 

connections and ensure a proper ground connection is made before connecting line 

voltage.

Содержание ComPac I AVP24







































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды