manualshive.com logo in svg

Marvair ComPac I AVP24, Руководство по эксплуатации продукта

Поделиться
Скачать
Marvair ComPac I AVP24 Скачать руководство пользователя страница 23

 

ComPac 6/09-18

Figure 7.   ComPac

®

 I and ComPac

®

 II A/C Wall Mount Detail (AVP24-72)

SUPPLY  AIR

RETURN  AIR

FOAM SEAL

DUCT EXTENSIONS (Not Supplied with Unit)

GRILLE

GRILLE

COMPAC® II  A/C

ONLY

2.7  Mounting The Unit (AVP24-72)

1.  For wiring into the back of unit, locate the lower of the two knockouts on the wall side of the unit.  

Drill  a one inch  hole in the shelter wall to match this opening.  Allow sufficient clearance  to run 

3/4" conduit through the hole and to the unit.

2.  Using an appropriate and safe lifting device, set the unit on the bottom support bracket mounted on 

the wall.  You must stabilize the unit on the bracket with the lifting device or by some other means 

- the bracket alone is not sufficient.  

3.   Make sure that the duct flanges are properly aligned with the wall opening.  Adjust as necessary.
4.  Note the holes in each side flange.  Using the holes for guides, drill  holes through the wall with a 

3/8" drill  bit.  Insert the 3/8" x 5" bolts through the flanges.  Install  nuts and washers on the inside 

of the shelter.  Tighten the bolts to secure the unit.

5.  Apply a bead of silicone where the mounting flange contacts the unit and the shelter wall.
6.  On the inside of the shelter, install the wall sleeves in the supply and return air openings.  The 

sleeves may be trimmed to fit flush with the inside wall. 

7.  Check the fit of each sleeve to its mating flange for possible air leaks. Apply silicone sealer to close 

any gaps.  Install the air return and supply grilles.

Содержание ComPac I AVP24







































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды