Marvair ComPac I AVP24 Скачать руководство пользователя страница 19

Страница: 19 / 38

ComPac 6/09-18

Installation Kits

The ComPac

I and ComPac

II A/C units, models AVP24-72, are shipped with one 12 Ga. "L" shaped

bottom bracket. On AVP24,30 & 36 units, there is an air intake hood packed inside each unit. If you

have not yet unpacked the unit, follow the instructions in section 2.1. All units have built-in full length

mounting flanges. Therefore, use of mounting brackets is not required.

Kit Components - Models AVP24-72:

1. One 12 Ga. "L"-shaped bottom bracket

Accessories:

The package may include other factory-supplied items (optional) as follows on the next page:

Codes:

Make sure your installation conforms to all applicable electrical, plumbing, building, and municipal

codes. Some codes may limit installation to single story structures.

Electrical Supply:

The power supply must have the appropriate voltage, phase, and ampacity for the model selected.

Voltage must be maintained above minimum specified values listed below. Refer to the data sticker

on the unit for ampacity requirements.

Table 4. Minimum Clearances

Table 5. Voltage Limitations

2.3 Installation Materials (AVP24-72)

Duct work should be designed and installed in accordance with

all

applicable safety codes and

standards. Marvair

strongly recommends referring to the current edition of the National Fire

Protection Association Standards 90A and 90B

before

designing and installing duct work.

The duct

system must be engineered to insure sufficient air flow through the unit to prevent over-heating of

the heater element. This includes proper supply duct sizing, sufficient quantity of supply registers,

and adequate return and filter areas. Duct work must be of correct material and must be properly

insulated. Duct work must be constructed of galvanized steel with a minimum thickness of .019

inches. Duct work must be firmly attached, secured, and sealed to prevent air leakage. See section

2.4 for additional duct work requirements.

Clearances:

Note the minimum clearances required for proper operation and service.

Electrical Rating Designations*

Nominal Voltage

208/230

460

Phase

Minimum Voltage

197

414

Maximum Voltage

253

506

* Letters refer to model number code designations. Refer to page 5.

MODEL

MIN. CLEARANCE AROUND

SIDES (SINGLE UNIT)

MIN. CLEARANCE BETWEEN

UNITS (TWO UNITS)

MIN. SPACE

ABOVE UNIT

30 inches

18 inches

24 inches

30/36

30 inches

18 inches

24 inches

42/48/60

30 inches

24 inches

30 inches

12 inches

Содержание ComPac I AVP24







































Результаты поиска

Содержание ComPac I AVP24

Отзывы:

Бренды по названию

Популярные бренды

Marvair ComPac I AVP24, Руководство по эксплуатации продукта

Результаты поиска

Содержание ComPac I AVP24

Отзывы:

Бренды по названию

Популярные бренды