background image

Before Operation 

Oil and Fuel 

POTENTIAL HAZARD 

• In certain conditions gasoline is extreme­

ly flammable and highly explosive.

WHAT CAN HAPPEN 

• A  fire  or  explosion  from  gasoline  can

burn  you,  others,  and  cause  property
damage.

HOW TO AVOID THE HAZARD 

• Use  a  funnel. and  fill  the  fuel  tank  out­

doors, in an open area, when the engine
is cold.  Wipe up any gasoline that spills.

• Do  not fill the fuel  tank  completely full.

Add  gasoline  to  the  fuel  tank  until  the

level  is  1/4"  to  1/2"  (6  mm to  13  mm)

below the bottom of the filler neck.  This

empty space in the  tank allows gasoline
to expand.

• Never  smoke  when  handling  gasoline,

and  stay  away  from  an  open  flame  or
where gasoline  fumes may be ignited by
a spark.

• Store  gasoline  in  an  approved  container

and keep it out of the reach of children.

• Never buy more than a 30-day supply of

gasoline.

1 .  Do  not smoke near fuel. 

2.

Mix  and pour  fuel  outdoors  and  where  there  are

no sparks or flames.

3.

Always  shut  off the  engine before  refueling.

Never remove the fuel tank cap while the engine is

running or just right after stopping the engine. 

POTENTIAL HAZARD 

• Gasoline  contains  gasses  that  can  build

up pressure inside a gas tank.

WHAT CAN HAPPEN 

• Fuel  can  be  spray e d   on  you  when

removing gas cap.

HOW TO AVOID TIIE HAZARD 

• Remove  fuel  cap  slowly  to  avoid  injury

from fuel spray.

4.

Always  open  the  fuel  tank  cap slowly  to release

any possible overpressure inside the tank.

5. 

6. 

7. 

8. 

Do not overfill the fuel  tank.  Stop filling 1/4-1/2 

inch (6 mm-13 mm) from the top of the tank. 

Tighten the fuel tank cap carefully but firmly after 

refilling. 

Wipe  up any  spilled  fuel  before  starting  the 

engme. 

Move the Hedge 'llimmer  at  least 10 feet (3  m) 

away from  the fueling location before starting 

the engine. 

10 feet (3 m) Minimum 

• 

[J 

-11-

Содержание EHT2300D

























Отзывы: