Maruyama AHT2600D-RS Скачать руководство пользователя страница 15

Страница: 15 / 16

- 14 -

Maintenance Interval

Before operating the Hedge Trimmer with Hedge Trimmer Attachment it is necessary to check the

adjustment of the cutting blades. Blades that are too loose may vibrate, and will not provide a clean,

smooth cut.

Cutting Blades Maintenance

CAUTION-BLADES THAT ARE TOO TIGHT CAN CAUSE OVERLOADING WHICH MAY DAMAGE

THE EQUIPMENT.

To adjust the cutting blades, refer to the illustrations and locate

the tension screws.

Loosen the tension screw and lock nuts. Gently turn the tension

screws in until sung, then turn the tension screws back out

1/3 -1/2 turn. While holding the screws in place, tighten the

lock nuts. Liberally coat the cutting blades with light oil.

Start the engine and operate the Hedge Trimmer at full speed

for at least one minute. Stop the engine, and when the blades

are motionless, touch the blades with your hand.

The blades may be warm, but if they are too hot to touch,

loosen the tension screws 1/8 turn.

Lubrication

Maintenance Interval

The gearcase and angle drive should be inspect after each 10 to 20

hours of use. Cutting blades should be lubricated at all times.

Lubrication

The gearcase and angle drive should be checked for lubrication

after each 10 to 20 hours of use. Grease fittings are installed into

both components. Use #2 lithium-base bearing lubricant.

Lubrication of the cutting blades should be maintained at all

times. Use a light oil (#10wt.).

General Cleaning and Tightening

The MARUYAMA Hedge Trimmer will provide maximum performance for many, many hours if it is

maintained properly. Good maintenance includes regular checking of all fasteners for correct tightness,

and cleaning the entire machine. Pitch and gum deposits should be removed from the cutting blades daily.

Adjustment of the cutting blade tension should be checked regularly.

Light Oil
(# 10wt.)

Grease Fitting

Cutting Blades

Flat Washer

Tension Screw

Guide Bar

Lock nut

Upper Blade

Lower Blade

【

Cross-sectional view of blades

】

Lock nut

Tension Screw



WARNING

POTENTIAL HAZARD

・

When engine is running, blades and other parts are moving.

WHAT CAN HAPPEN

・

Contact with moving blades or other moving parts could cause serious personal injury or death.

HOW TO AVOID THE HAZARD

・

Always turn off your Hedge Trimmer before you clean or perform any maintenance on it.

Содержание AHT2600D-RS

















Результаты поиска

Содержание AHT2600D-RS

Отзывы:

Бренды по названию

Популярные бренды

Maruyama AHT2600D-RS, Руководство владельца/оператора

Результаты поиска

Содержание AHT2600D-RS

Отзывы:

Бренды по названию

Популярные бренды