Maruyama AHT2600D-RS Скачать руководство пользователя страница 11

Страница: 11 / 16

- 10 -

5. Make sure the blades are moving (at least half throttle ) before actual

cutting begins. The Hedge Trimmer performs best at full throttle.

6. Always release the throttle trigger and allow the engine to return to

speed when not cutting.

7. Stop the engine when moving between work sites.

・

If the blades becomes jammed, stop the engine immediately.

・

Make certain all moving parts have stopped and disconnect the

spark plug before inspecting the equipment for damage.

・

Never use a unit that has chipped, cracked or broken blades.

IMPORTANT: The thickness of branches which may be cut using this

trimmer is limited to up to approximately 4.5mm. Never try to cut

branches thicker than this, as doing so may result in damage to

the trimmer.

8. When transporting the Hedge Trimmer always fit the blade cover.

IMPORTANT:
To detach the shoulder hanging strap quickly from the Hedge Trimmer, pull upward on the red band.

Adjusting the angle of the blades

Note:

Never use the unit if blade angle is not from 48 degree

upwards to 84 degree downward.

①

First of all, stop the engine, then set the blade cover.

②

Turn the clamp knob counter clockwise until the clamp

knob stops. Angle adjusting is not possible without complete

loosen the clamp knob.

③

Always hold the handle when adjust the blades.

The blades are able to adjust the angle from 48 degee

upward to 84 degree downward.

Never push the lock lever when adjusting the angle of the

blades.

④

After adjusting the angle, tighten the clamp knob firmly

and fix the garcase. When tighten the clamp knob, make

sure both racks steady engagement.



CAUTION

・

Do not touch the sharpened edges of the cutting blades. The cutting blades are extremely

sharp and dangerous at all times. Always wear gloves to help protect your hands and fingers
from injury.

・

Do not hold any other part except the handle when adjusting the angle of the blades.

・

Stop the engine and set the blade cover when adjusting the angle of the blades.

Down To 84°

Clamp Knob

Handle

Blade
Cover

Lock Lever
(Push to downward)

Gearcase

Check the racks
steady engagement

Up To 48°

Tighten

Loosen

Strap

Ring

Red Band

Hook

Engaged

Not
Engaged

Содержание AHT2600D-RS

















Результаты поиска

Содержание AHT2600D-RS

Отзывы:

Бренды по названию

Популярные бренды

Maruyama AHT2600D-RS, Руководство владельца/оператора

Результаты поиска

Содержание AHT2600D-RS

Отзывы:

Бренды по названию

Популярные бренды