NOTE:
AN INDICATION ON THE P/E LAMP DOES NOT
INDICATE A SATISFACTORY EARTH
5.
SPECIFICATION
5.1
ELECTRICAL
Supply Voltage:
200 to 260V rms, 50/60Hz
Test Current:
24A, rms, for two half cycles at 240V
Loop Range:
0 to 15
W
nominal in steps of 0.01
W
15 to 199.9
W
in steps of 0.1
W
Accuracy:
±2% of reading, ±2 digit
Temperature Coefficient: ±0.1%/°C
Ipsc Range:
0 to 19.99kA in steps of 0.01kA
Fuse:
5A, HBC, Anti-Surge ceramic,
DIN 5 X 20mm
Transient Protection:VDR at input
Thermal Protection: Electronic delay
Safety:
EMC: To
BS EN 50081-1
BS EN 50082-1
LVD: To
BS EN 61010-1
Installation Category:
Catergory III
NOTE:
AN INDICATION ON THE P/E LAMP DOES NOT
INDICATE A SATISFACTORY EARTH
5.
SPECIFICATION
5.1
ELECTRICAL
Supply Voltage:
200 to 260V rms, 50/60Hz
Test Current:
24A, rms, for two half cycles at 240V
Loop Range:
0 to 15
W
nominal in steps of 0.01
W
15 to 199.9
W
in steps of 0.1
W
Accuracy:
±2% of reading, ±2 digit
Temperature Coefficient: ±0.1%/°C
Ipsc Range:
0 to 19.99kA in steps of 0.01kA
Fuse:
5A, HBC, Anti-Surge ceramic,
DIN 5 X 20mm
Transient Protection:VDR at input
Thermal Protection: Electronic delay
Safety:
EMC: To
BS EN 50081-1
BS EN 50082-1
LVD: To
BS EN 61010-1
Installation Category:
Category III
the tester passes up to 24A to earth during a test for up to 2 half
cycles.
It will therefore probably be necessary to bypass the RCD with
links during the test, making sure that the links are removed
after the test. With the RCD bridged, the protection of the circuit
against earth faults is removed and precautions should be taken
to ensure that the circuit is not used when the RCD is
inoperative.
It will be necessary to isolate the live side of the RCD before
inserting and removing links. Depending upon the type of
installation, the electricity supply authority may have to be
consulted before the supply can be isolated.
4.
WIRING FAULT DIAGNOSIS
The two neon lamps indicate the status of the socket phase-
neutral and phase-earth conductors and so can be interpreted
to diagnose the wiring fault in the socket.
The table below aids this diagnosis.
Lamp on:
X
Lamp off:
O
the tester passes up to 24A to earth during a test for up to 2 half
cycles.
It will therefore probably be necessary to bypass the RCD with
links during the test, making sure that the links are removed
after the test. With the RCD bridged, the protection of the circuit
against earth faults is removed and precautions should be taken
to ensure that the circuit is not used when the RCD is inoperative.
It will be necessary to isolate the live side of the RCD before
inserting and removing links. Depending upon the type of
installation, the electricity supply authority may have to be
consulted before the supply can be isolated.
4.
WIRING FAULT DIAGNOSIS
The two neon lamps indicate the status of the socket phase-
neutral and phase-earth conductors and so can be interpreted
to diagnose the wiring fault in the socket.
The table below aids this diagnosis.
Lamp on:
X
Lamp off:
O
-8-
-9-
p
m
a
L
l
a
r
t
u
e
N
.
n
n
o
c
s
i
D
e
s
a
h
P
.
n
n
o
c
s
i
D
&
e
s
a
h
P
l
a
r
t
u
e
N
d
e
s
r
e
v
e
R
h
t
r
a
E
.
n
n
o
c
s
i
D
&
e
s
a
h
P
h
t
r
a
E
d
e
s
r
e
v
e
R
N
/
P
O
O
X
X
O
E
/
P
X
O
O
O
X
-8-
-9-
p
m
a
L
l
a
r
t
u
e
N
.
n
n
o
c
s
i
D
e
s
a
h
P
.
n
n
o
c
s
i
D
&
e
s
a
h
P
l
a
r
t
u
e
N
d
e
s
r
e
v
e
R
h
t
r
a
E
.
n
n
o
c
s
i
D
&
e
s
a
h
P
h
t
r
a
E
d
e
s
r
e
v
e
R
N
/
P
O
O
X
X
O
E
/
P
X
O
O
O
X
WE RECOMMEND THAT, IF THIS
INSTRUMENT IS USED FOR VERIFYING
ELECTRICAL INSTALLATIONS, IT IS
RE-CALIBRATED EVERY 12 MONTHS
WE RECOMMEND THAT, IF THIS
INSTRUMENT IS USED FOR VERIFYING
ELECTRICAL INSTALLATIONS, IT IS
RE-CALIBRATED EVERY 12 MONTHS
Содержание LP2000
Страница 2: ......
