background image

4

Juggler User Manual

 

S

AFETY

 

PRECAUTIONS

The Juggler is not for household use. It is not a toy: it presents risks of serious
injury due to electric shock, high heat, and intense light. For safe operation, read
this manual before using the fixture and observe all warnings and precautions
printed here and on the fixture. If you have questions about how to operate the
fixture safely, please contact your Martin distributor or dealer.

For protection against dangerous electric shock, always ground (earth) the 
fixture electrically. Use only a source of AC power that complies with local 
building and electrical codes.

Replace the lamp if it becomes defective or worn out. Allow the fixture to cool 
for 5 minutes before installing a new lamp.

Keep all combustible materials (for example fabric, wood, paper) at least 30 
cm (12 inches) away from the fixture. Keep flammable materials well away 
from the fixture.

Provide a minimum clearance of 10 cm (4 inches) around the fan and air vent. 

When suspending the fixture above ground level, verify that the structure can 
hold at least 10 times the weight of all installed devices and secure the fixture 
with an approved safety cable. Block access below the work area whenever 
installing or removing the fixture. 

Never remove any cover except the lamp access cover. Refer all service to a 
qualified technician. 

Do not expose the fixture to rain or moisture.

Do not illuminate surfaces within 1 m (39 inches) of the fixture.

Do not operate the fixture if the ambient temperature exceeds 40° C 
(104° F).

NEVER place filters or other objects over the lens or mirror. 

Содержание Juggler












Отзывы: