Martin Audio Wavefront W8CT Скачать руководство пользователя страница 57 | Manualshive

Страница: 57 / 247

background image

2.6

Power amplifier recommendations

Wavefront Longthrow loudspeakers have been designed and manufactured for very
high performance over great distances. They are very easy - particularly if power
amplifier racks and controllers are standardised within a system.

Power capability

W8CTs and W8CMs will provide full performance when driven by professional
power amplifiers capable of delivering undistorted output power into a range of loads
as follows:

W8CT & W8CM

250-300W(av) into 8 ohms,
500-600W(av) into 4 ohms
and
1,000-1,200W(av) into 2 ohms.

Please note:

Amplifiers with inadequate headroom before clipping may age high frequency
components due to excessive signal density.

Amplifiers with excessive output may damage voice-coils or age driver suspensions
due to excessive heat dissipation and excursion.

A note about power amplifier output specifications

Most power amplifier manufacturers keep their costs down by using unregulated
supply rails which sag under load. To allow for this sag, manufacturers set their rails
high so that they still meet their quoted output into specified loads. These high rail
voltages allow such power amplifiers to provide outputs 1.5 - 2 times their quoted
power for short-term bursts. Martin Audio products will withstand this potential
doubling of instantaneous power -

with suitably set controller limiters

- but further,

long-term increases caused by oversized amplifiers should be avoided.

Martin Audio MA series power amplifiers have regulated rails so it is quite
permissible to use slightly overpowered models -

with suitably set controller limiters

-

without risking uncontrolled power bursts. The MA series power amplifiers’
regulated power rails also ensure maximum performance under the real-world concert
conditions of less-than-optimum mains supplies and low impedance loads.

See

Section 1.6.1

for information on the Martin Audio MA2.8 power amplifier.

All material © 2007. Martin Audio Ltd. Subject to change without notice.

«
...
55
56
57
58
59
...
»

Содержание Wavefront W8CT
























































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Wavefront W8CT

Бренд: ABB Страницы: 2

Бренд: Icy Box Страницы: 8

Бренд: Panduit Страницы: 2

Бренд: Xigmatek Страницы: 17

Бренд: Xigmatek Страницы: 14

Бренд: Geekworm Страницы: 2

Бренд: Center Страницы: 11

Бренд: Minebea Intec Страницы: 24

Бренд: Promise Technology Страницы: 354

Бренд: Icy Box Страницы: 10

Бренд: Icy Box Страницы: 16

Бренд: Icy Box Страницы: 23

Бренд: Peavey Страницы: 2

Бренд: Velleman Страницы: 32

U457-2M2-SATAG2

Бренд: Tripp Lite Страницы: 32

Бренд: Hunter Страницы: 2

Бренд: IBM Страницы: 46

Express Storage

Бренд: Hama Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды