manualshive.com logo in svg

Martin Audio Wavefront W8CT, Инструкция по применению

Поделиться
Скачать
Martin Audio Wavefront W8CT Скачать руководство пользователя страница 198

1.5.2 DX1 Output Gain and Limiter settings for the W8

Standardising on one good model of power amplifier (preferably the 

Martin Audio

MA2.8

) and correctly set-up controller (preferably the

 

Martin Audio DX1

) will

provide the most dynamic system performance and protection whilst simplifying
design and reducing spares inventories.

Gain settings

The following DX1 output gain settings will enable full system performance to be
obtained whilst keeping the console and drive system noise floors inaudible and
avoiding amplifier slew-rate limiting:

W8 - assuming 300Wcont - 600Wpk into 8

Ω

Ω

 power amplifiers:

Best-fit

Initial DX1

Amplifier

Amplifier

Amplifier

Output GAIN

Example

Sensitivity

Gain

Lomid Himid High

dBu

Vrms dB

dB

dB

dB

Martin MA2.8* (38dB)

-2

0.62

38

-9

-9

-7

Crest CA9 (x68)

-1

0.69

37

-8

-8

-6

Crown MA1202 (0.775v)

0

0.77

36

-7

-7

-5

+1

0.87

35

-6

-6

-4

QSC PL224

+2

0.98

34

-5

-5

-3

+3

1.09

33

-4

-4

-2

Martin MA2.8* (32dB)

+4

1.23

32

-3

-3

-1

Crest 4801 (x40)

+4

1.23

32

-3

-3

-1

Crown K1 (1.4v)

+4

1.23

32

-3

-3

-1

QSC PL218/218A (32dB)

+4

1.23

32

-3

-3

-1

QSC PL224A (32dB)

+4

1.23

32

-3

-3

-1

Crown MA1202 (1.4v)

+5

1.38

31

-2

-2

0

+6

1.55

30

-1

-1

+1

+7

1.73

29

0

0

+2

+8

1.95

28

+1

+1

+3

+9

2.18

27

+2

+2

+4

Crown MA1202 (26dB)

+10

2.45

26

+3

+3

+5

Crown K1 (26dB)

+10

2.45

26

+3

+3

+5

QSC PL218A (26dB)

+10

2.45

26

+3

+3

+5

QSC PL224A (26dB)

+10

2.45

26

+3

+3

+5

* Set Martin Audio MA2.8 rear MLS switch to -2dB to match peak output of
unregulated power amplifiers.

Cluster balance (eg farfield-to-nearfield or inner-to-outer) should be adjusted 

at the

power amplifier controls

 to maintain limiter tracking. See 

Section A1.7.

Balancing the system using gain controls in the signal path 

before

 the power

amplifiers will cause the higher signal level upper row of a big cluster to start limiting
before the lower signal levels downfills causing tonal changes at the mix position.

All material © 2007. Martin Audio Ltd. Subject to change without notice.

Содержание Wavefront W8CT
























































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды