Martin Audio Wavefront W8CT Скачать руководство пользователя страница 201 | Manualshive

Страница: 201 / 247

background image

The DX1 may be user-programmed to many more touring and fixed installation
configurations based on its 2 input + sum, 6 output matrix. This operation is best
completed by an audio technician who is familiar with DSP-based pro-audio.

(See separate

DX1 Speaker Management System User's Guide

for details)

A1.6 Power amplifier recommendations

Wavefront Series loudspeaker systems have been designed and manufactured for very
high performance and arrayability. The systems are very easy to use - particularly if
power amplifier racks and controller settings are standardised within a system.

Power capability

The Wavefront W8 will provide full performance when driven by professional power
amplifiers capable of delivering undistorted output power into a range of loads as
follows:

W8

250-300W(AES) into 8 ohms,
500-600W(AES) into 4 ohms
and
1,000-1,200W(AES) into 2 ohms.

Please note:

Amplifiers with inadequate headroom before clipping may age high frequency
components due to excessive signal density.

Amplifiers with excessive output may damage voice-coils or age driver suspensions
due to excessive heat dissipation and excursion.

A note about power amplifier output specifications

Most power amplifier manufacturers keep their costs down by using unregulated
supply rails which sag under load. To allow for this sag, manufacturers set their rails
high so that they still meet their quoted output into specified loads. These high rail
voltages allow such power amplifiers to provide outputs 1.5 - 2 times their quoted
power for short-term bursts. Martin Audio products will withstand this potential
doubling of instantaneous power - with suitably set controller limiters - but further,
long-term increases caused by oversized amplifiers should be avoided.

Martin Audio MA Series Power Amplifiers

Martin Audio MA Series amplifiers have regulated rails so it is quite permissible to
use slightly overpowered models - with suitably set controller limiters - without
risking uncontrolled power bursts. The MA series power amplifiers’ regulated power

All material © 2007. Martin Audio Ltd. Subject to change without notice.

«
...
199
200
201
202
203
...
»

Содержание Wavefront W8CT
























































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Wavefront W8CT

WJHDE300 - DIGITAL DISK RECORDER

Бренд: Panasonic Страницы: 20

Бренд: Red4Power Страницы: 28

Pure 591 415 01, Pure 591 417 01, Pure 591 515 01, Pure 591 517 01 Smart 591 435 01

Бренд: Spelsberg Страницы: 36

Бренд: Rosewill Страницы: 13

Бренд: AFL Страницы: 14

Бренд: XCLIO Страницы: 4

Бренд: Digital Watchdog Страницы: 2

SmartRack SRW12USNEMA

Бренд: Tripp Lite Страницы: 2

Shura TQE-2223B

Бренд: TOOQ Страницы: 38

Бренд: Macally Страницы: 18

Бренд: PairGain Страницы: 20

Бренд: Icy Dock Страницы: 2

Spectrum MediaDirector

Бренд: Harmonic Страницы: 82

Бренд: I-bus/Phoenix Страницы: 48

Universal Shelter

Бренд: DAVIS Страницы: 8

Бренд: Eaton Страницы: 86

Бренд: GAMDIAS Страницы: 13

MIC-3038 Series

Бренд: Advantech Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды