Martin Audio Wavefront Precision Series страница 44 Скачать руководство пользователя

Страница: 44 / 45

WPS USER GUIDE V1.0

WPS USER GUIDE

Specifications

WPS Specifications

TYPE

Three-way, passive line array element

FREQUENCY RESPONSE

70Hz-18000Hz ± 3dB

DRIVERS

LF: 2 x 8” (200mm)/2” (50mm) voice coil, long excursion,

vented yoke, neodymium magnet drivers

MF: 4 x 4” (100mm)/1” (25mm) coil, neodymium magnet

drivers, compression loaded

HF: 4 x 1” (25mm) exit/1.4” (35mm) HT Polymer diaphragm,

neodymium magnet compression drivers

SYSTEM AMPLIFIER

iKON iK42

SYSTEM RESOLUTION

1 to 3 enclosures per amplifier channel (iK42)

MAXIMUM SPL

LF: 133dB (peak)

NOMINAL IMPEDANCE

6 ohms

DISPERSION

100º horizontal (-6dB), 120º horizontal (-10dB), 10° vertical

CROSSOVER

520Hz, 1.6kHz internal passive

ENCLOSURE

Vertical trapezoid with 5º wall angle,

multi-laminate birch and poplar-ply construction

FINISH

Black textured paint

PROTECTIVE GRILLE

Black HEX perforated steel

CONECTORS

2 x NL4 type

PIN CONNECTIONS

1+/1-

FITTINGS

3-point rigging system, 2 x side pocket handles

2 x rear grip handles

FLOWN ARRAY MAXIMUM

16 (installation) and 24 (touring) enclosures in a single ar

DIMENSIONS (ex. pins)

(W) 650mm x (H) 261mm x (D) 400mm

(W) 25.6in x (H) 10.3in x (D) 15.8in

WEIGHT

27kg (60lbs)

ACCESSORIES

WPSGRIDi – Install fying frame

WPSGRIDt – Touring flying frame

WPSOUTRIG – Ground-stacking accessories

IK42AMPRACK-UK+ – Fully populated amplifier rack (Euro)

IK42AMPRACK-US+ – Fully populated amplifier rack (US)

WPSCART – Transport cart

ASM20017 – Inclinometer sensor

ASM20019 – Inclinometer reader

Содержание Wavefront Precision Series












































Результаты поиска

Содержание Wavefront Precision Series

Отзывы:

Похожие инструкции для Wavefront Precision Series

Бренды по названию

Популярные бренды

Martin Audio Wavefront Precision Series, Руководство пользователя

Результаты поиска

Содержание Wavefront Precision Series

Отзывы:

Похожие инструкции для Wavefront Precision Series

Бренды по названию

Популярные бренды