Martin Audio Wavefront Precision Series Скачать руководство пользователя страница 32 | Manualshive

Страница: 32 / 45

background image

Copyright © 2019 Martin Audio Ltd.

32

WPS USER GUIDE V1.0

WPS USER GUIDE

Attach the rear link from the top cabinet to the flying frame in the LINK position.

Insert the pin into the LINK hole on the flying frame.

Lift the array until the transport cart is just clear of the ground. As the array goes up the cabinets will open to the angles that you have
preselected from the DISPLAY project prediction. Insert the lock pin at the LOCK position on each cabinet to lock the inter-cabinet angles.
At this stage the cable loom should be attached to the grid and the first four cabinets connected. As more cabinets are added they should
be connected to the loom and link cables between cabinets connected where required. Cables are not shown for clarity.

«
...
30
31
32
33
34
...
»

Содержание Wavefront Precision Series














































Отзывы:

Нет отзывов

Похожие инструкции для Wavefront Precision Series

Бренд: JeaTone Страницы: 6

Бренд: Yamaha Страницы: 86

Бренд: Jam Страницы: 32

Бренд: Jam Страницы: 14

MIG 208 Alu Synergy

Бренд: Magnum Страницы: 24

Бренд: MAGNEPLANAR Страницы: 4

Бренд: Nelson Страницы: 18

Бренд: Nelson Страницы: 150

Water Jet Lightning

Бренд: Oase Страницы: 28

Бренд: Oase Страницы: 9

Бренд: WaterLogic Страницы: 29

EcoTouch Ai1 Geo

Бренд: WATERKOTTE Страницы: 60

Бренд: Mackie Страницы: 6

Бренд: JBL Страницы: 6

Бренд: Vimar Страницы: 40

Бренд: NewArc Страницы: 12

Бренд: Bigben Страницы: 56

Бренд: Monitor Audio Страницы: 13

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды