Montage- und Betriebsanleitung
Installation and Safety Instructions
15
EN
33..55
G
Geenneerraall w
waarrnniinnggss aanndd ssaaffeettyy iinnssttrruuccttiioonnss
W
WAARRN
NIIN
NG
G
DDaannggeerr ffrroom
m uussee bbyy uunnttrraaiinneedd aanndd uunnaauutthhoorriisseedd ppeerrssoonnnneell!!
The clamping or assembly of a tool and its components or the setting and in-
stallation on a machine tool by unqualified and/or unauthorised personnel can
result in hazardous situations.
Only trained, authorised and dependable specialist personnel may clamp, as-
semble and set tools and install them on a machine tool.
The specialist personnel must be able to recognise and avoid hazards.
CCAAU
UTTIIO
ON
N
SShhaarrpp ccuuttttiinngg eeddggeess oonn tthhee ttooooll!!
Sharp cutting edges may cause cutting injuries.
Wear protective gloves when changing tools.
N
NOOTTIICCEE
DDaam
maaggee ttoo tthhee ttooooll ccuuttttiinngg eeddggeess!!
If the tool is placed with the cutting edge facing upwards, the cutting edges of
the tool can be damaged.
Do not place the tool on the cutting edges.
N
NOOTTIICCEE
W
Weeaarr dduuee ttoo uussee ooff aa ppoow
weerr ssccrreew
wddrriivveerr ffoorr ttiigghhtteenniinngg tthhee ccllaam
mppiinngg ssccrreew
w!!
Use of a power screwdriver for tightening the clamping screw will result in in-
creased wear of the clamping set.
Tighten the clamping screw only manually.
IIN
NFFO
ORRM
MAATTIIO
ON
N
The indexable inserts may only be changed by trained personnel!
14
Montage- und Betriebsanleitung
Installation and Safety Instructions
EN
SSaaffeettyy
33..11
TTaarrggeett ggrroouupp
The HPR400 plus may only be used by trained, authorised and dependable spe-
cialist personnel. The specialist personnel must be able to recognise and avoid
hazards and for this purpose must have read this document before using the High
Performance Reamer HPR400 plus.
The health and safety regulations, safety stipulations and instructions from the
machine manufacturer are familiar to the specialist personnel and are to be fol-
lowed and observed during operation of the tool.
33..22
CCoorrrreecctt uussee
•
The HPR400 plus and its components are intended only for cutting operations
during manufacturing on machine tools in industrial applications.
•
The HPR400 plus and its components may only be used when observance of
all the information contained in this document is assured.
•
Failure to observe these instructions can result in injuries or damage to ma-
chines and accessories for which MAPAL assumes no liability.
33..33
IInnccoorrrreecctt uussee
•
The HPR400 plus and its components must not be modified or used for any
other applications.
•
Unauthorised modifications to the tool and its components or use for other
than the intended purpose will void all warranty claims against MAPAL.
•
The manufacturer assumes no liability for accidents or damage resulting
from use for other than the correct use.
33..44
W
Waarrrraannttyy
The warranty period is 2244 m
moonntthhss from the date of ex works delivery.
The tool, including all its components and accessories, must not be modified or
used for non-authorised applications. Any modification to the tool or any unau-
thorised use will void all warranty claims against MAPAL.
MAPAL expressly declines any liability for accidents or damage resulting from the
use of damaged tools or damaged machine parts. Wear parts are not covered by
the warranty.
Montage- und Betriebsanleitung
Installation and Safety Instructions
14
EN
