Manitowoc S model Скачать руководство пользователя страница 67 | Manualshive

Страница: 67 / 72

background image

Section 4

Maintenance

Part Number 000002477 3/08

4-13

Guardian

This product can be used on models S600C/S850C/
S1000C/S1200C/S1470C/S1870C/S2170C - this
product cannot be used on IB600C/IB800C/IB1000C
due to space constraints. Slime is a leading cause of ice
machine breakdowns and biological growth is a health
concern. The Guardian system releases chlorine dioxide
on a controlled basis to inhibit the growth of bacteria and
fungi that form slime and cause malodors in the food
zone of ice machines.

The Guardian will not control mineral or other water
borne buildup. Your water quality will determine the
length of time before mineral buildup affects ice machine
performance. Mineral buildup must be removed as often
as necessary to ensure trouble-free operation of the ice
machine.

The Guardian sachet holder is included with the sachet
packets. Refer to installation/replacement procedure to
install/change sachet holder/ packet.

Guardian Location

GUARDIAN SACHET REPLACEMENT FREQUENCY

Sachet packet(s) require replacement every thirty (30)
days or whenever they come in direct contact with water.
Refer to chart below for requirements.

Guardian sachet packets are available through your
local Manitowoc ice machine dealer.

SACHET INSTALLATION/REPLACEMENT
PROCEDURE

1. Loosen the left screw and open the left front door.

The right front panel does not need to be removed.

Screw Location

2. Inside the front panel there are two pegs for

mounting the sachet holder.

S1470C/S1870C/S2170C

Only

- The sachet holder mounts to the front top

support (mounting holes may be covered by
insulation).

3. Attach the sachet holder to the front panel by

hanging on the pegs.

S1470C/S1870C/S2170C Only

-

Attach sachet holder with reusable ties.

4. Remove the new sachet packet from foil package

and install into holder. Removing the foil package
allows moisture in the air to activate the sachet
contents.

5. Close the left front door and tighten the screw.

6. Discard the used sachet packet in the trash.

CLEAN UP PROCEDURE FOR DAMAGED SACHET
PACKET

1. Remove all ice from bin/dispenser and discard.

2. Initiate a cleaning and sanitizing sequence on the

ice machine.

3. Clean the bin/dispenser. Flush the drain thoroughly

to prevent future drain blockage.

4. Sanitize the bin/dispenser.

5. Install a replacement sachet packet and reinstall all

panels.

Ice Machine

Sachet Use

S600C

1

S850C/S1000C/S1200C/S1470C/S2170C

1 or 2*

*Although one sachet is recommended, extreme conditions may
necessitate using two sachet packets.

Guardian

Inside Left
Front Door

Loosen

Screw

«
...
65
66
67
68
69
...
»

Содержание S model









































































Отзывы:

Нет отзывов

Похожие инструкции для S model

Sanitizer Plus ASP1-1044

Бренд: Water Right Страницы: 30

Бренд: Eastwood Страницы: 16

Бренд: Follett Страницы: 24

Бренд: Marlo Incorporated Страницы: 24

Бренд: DE VECCHI Страницы: 24

Бренд: Victory Страницы: 2

Бренд: Victory Страницы: 6

Majestic SK15MAJ

Бренд: Silver King Страницы: 12

Majestic SK18MAJ

Бренд: Silver King Страницы: 12

Бренд: Silver King Страницы: 10

Бренд: Metcal Страницы: 5

Hypercool WFA Series

Бренд: Parker Hiross Страницы: 52

Bag & Overstrom B3 728

Бренд: RSL Страницы: 5

Бренд: Piusi Страницы: 2

Бренд: Piusi Страницы: 29

Бренд: Kripsol Страницы: 8

Бренд: AVANT Страницы: 26

Бренд: Madell Страницы: 5

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды