Manitou MHT 10180 LT-E3 Скачать руководство пользователя страница 14 | Manualshive

Страница: 14 / 223

background image

1-8

OPERATING INSTRUCTIONS UNLADEN AND LADEN

A - BEFORE STARTING THE LIFT TRUCK

- Carry out daily maintenance (see: 3 - MAINTENANCE: A - DAILY OR EVERY 10 HOURS SERVICE).
- Make sure the lights, indicators and windscreen wipers are working properly.
- Make sure the rear view mirrors are in good condition, clean and properly adjusted.
- Make sure the horn works.

B - DRIVER’S OPERATING INSTRUCTIONS

- Whatever his experience, the operator is advised to familiarize himself with the position and operation of all the controls and instruments

before operating the lift truck.

- Wear clothes suited for driving the lift truck, avoid loose clothes.
- Make sure you have the appropriate protective equipment for the job to be done.
- Prolonged exposure to high noise levels may cause hearing problems. It is recommended to wear ear muffs to protect against excessive

noise.

- Always face the lift truck when getting into and leaving the driving seat and use the handle(s) provided for this purpose. Do not jump

out of the seat to get down.

- Always pay attention when using the lift truck. Do not listen to the radio or music using headphones or earphones.
- Never operate the lift truck when hands or feet are wet or soiled with greasy substances.
- For increased comfort, adjust the seat to your requirements and adopt the correct position in the driver’s cab.

Under no circumstances must the seat be adjusted while the lift truck is moving.

- The operator must always be in his normal position in the driver’s cab. It is prohibited to have arms or legs, or generally any part of the

body, protruding from the driver’s cab of the lift truck.

- The safety belt must be worn and adjusted to the operator’s size.
- The control units must never in any event be used for any other than their intended purposes (e.g. climbing onto or down from the lift

truck, portmanteau, etc.).

- If the control components are fitted with a forced operation (lever lock) device, it is forbidden to leave the cab without first putting these

controls in neutral.

- It is prohibited to carry passengers either on the lift truck or in the cab.

«
...
12
13
14
15
16
...
»

Содержание MHT 10180 LT-E3
































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MHT 10180 LT-E3

Бренд: Telwin Страницы: 108

Brauheld Pro 30

Бренд: Klarstein Страницы: 32

Бренд: V-ZUG Страницы: 24

Бренд: Abicor Binzel Страницы: 160

Pulstronic 2011 Mod. 313

Бренд: Suevia Страницы: 40

DRINKWORKS Home Bar Classic

Бренд: Keurig Страницы: 32

HEAVY DUTY HOIST

Бренд: Proslat Страницы: 6

EduTrainer 8071407

Бренд: Festo Страницы: 80

Бренд: MESA Electronic Страницы: 19

Бренд: Campbell Hausfeld Страницы: 68

Бренд: Yeswelder Страницы: 8

Бренд: AUTO ARC Страницы: 16

Бренд: morse Страницы: 6

Бренд: Raven Страницы: 60

Бренд: Viessmann Страницы: 44

Бренд: Raven Страницы: 50

Бренд: National Instruments Страницы: 8

FlexRIO NI 6581

Бренд: National Instruments Страницы: 22

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды