Maktec MT372 Скачать руководство пользователя страница 10

10

Straight guide

The straight guide is effectively used for straight cuts 
when chamfering or grooving. 

(Fig. 11)

Attach the guide plate to the straight guide with the bolt 
and the wing nut. 

(Fig. 12)

Remove the guide holder and the chip deflector.
Attach the straight guide with the clamping screw (A). 
Loosen the wing nut on the straight guide and adjust the 
distance between the bit and the straight guide. At the 
desired distance, tighten the wing nut securely. 

(Fig. 13)

When cutting, move the tool with the straight guide flush 
with the side of the workpiece.
If the distance (A) between the side of the workpiece and 
the cutting position is too wide for the straight guide, or if 
the side of the workpiece is not straight, the straight guide 
cannot be used. In this case, firmly clamp a straight board 
to the workpiece and use it as a guide against the trimmer 
base. Feed the tool in the direction of the arrow. 

(Fig. 14)

Circular work

Circular work may be accomplished if you assemble the 
straight guide and guide plate.
Min. and max. radius of circles to be cut (distance 
between the center of circle and the center of bit) are as 
follows:
Min.: 70 mm
Max.: 221 mm

For cutting circles between 70 mm and 121 mm in 
radius. (Fig. 15)

For cutting circles between 121 mm and 221 mm in 
radius. (Fig. 16)

NOTE:

• Circles between 172 mm and 186 mm in radius cannot 

be cut using this guide.

Align the center hole in the straight guide with the center 
of the circle to be cut. Drive a nail less than 6 mm in 
diameter into the center hole to secure the straight guide. 
Pivot the tool around the nail in clockwise direction. 

(Fig. 17)

Trimmer guide

Trimming, curved cuts in veneers for furniture and the like 
can be done easily with the trimmer guide. The guide 
roller rides the curve and assures a fine cut. 

(Fig. 18)

Attach the chip deflector on the groove of the base. Then 
install the trimmer guide and guide holder on the tool base 
with the clamping screw (A). Loosen the clamping screw 
(B) and adjust the distance between the bit and the 
trimmer guide by turning the adjusting screw (1 mm per 
turn). At the desired distance, tighten the clamping screw 
(B) to secure the trimmer guide in place. 

(Fig. 8)

When cutting, move the tool with the guide roller riding the 
side of the workpiece. 

(Fig. 19)

MAINTENANCE

CAUTION:

• Always be sure that the tool is switched off and 

unplugged before attempting to perform inspection or 
maintenance.

• Never use gasoline, benzine, thinner, alcohol or the 

like. Discoloration, deformation or cracks may result.

Replacing carbon brushes

Remove and check the carbon brushes regularly. Replace 
when they wear down to the limit mark. Keep the carbon 
brushes clean and free to slip in the holders. Both carbon 
brushes should be replaced at the same time. Use only 
identical carbon brushes. 

(Fig. 20)

Use a screwdriver to remove the brush holder caps. Take 
out the worn carbon brushes, insert the new ones and 
secure the brush holder caps. 

(Fig. 21)

To maintain product SAFETY and RELIABILITY, repairs, 
any other maintenance or adjustment should be 
performed by Makita Authorized Service Centers, always 
using Makita replacement parts.

OPTIONAL ACCESSORIES

CAUTION:

• These accessories or attachments are recommended 

for use with your Makita tool specified in this manual. 
The use of any other accessories or attachments might 
present a risk of injury to persons. Only use accessory 
or attachment for its stated purpose.

If you need any assistance for more details regarding 
these accessories, ask your local Makita Service Center.

Router bits

Straight bit (Fig. 22)

mm

006485

“U” Grooving bit (Fig. 23)

 mm

006486

“V” Grooving bit (Fig. 24)

mm

006454

Drill point flush trimming bit (Fig. 25)

 mm

006487

D

A

L1

L2

20

6

20

50

15

20E

1/4"

8

6

8

50

18

8E

1/4"

6

6

6

50

18

6E

1/4"

D

A

L1

L2

R

6

6

6

60

28

3

6E

1/4"

D

A

L1

L2

θ

1/4"

20

50

15

90°

D

A

L1

L2

L3

6

6

6

60

18

28

6E

1/4"

Содержание MT372

































Отзывы: