MAKSIWA CBC.EC, Инструкция по эксплуатации

Страница: 9 / 18

9
wood or the tape.
IMPORTANT:
All maintenance or cleaning on the machine must be
made with the same OFF and unplugged from the
outlet to prevent accidental discharges.
GENERAL
Periodic maintenance on your Edgebander CBC.E
MAKSIWA will ensure optimum performance. Make it
a habit to inspect your edgebander every time you
use it.
This section covers the service adjustments or
common procedures that may need to be made
during the life of your machine.
Verify if the following conditions for repair or
replacement are needed:
• Loosen screws.
• Switches or buttons damaged.
• Cables, plugs or sockets worn or damaged.
• Transmission chain damaged.
• Dirt Glue axis or glue pot. The dust coming from
saw machines can lock the axis. Keep your CBC.E as
distantly as possible of saw machines.
• Any other condition that could adversely affect the
safe operation of the equipment.
CLEANING
Clean your Edgebander CBC.E is relatively easy. Use
a vacuum cleaner to remove the tape remains, and
dusting with a dry cloth. If there is any glue residue
use a resin remover and a clean cloth to remove it.
Keep the table clean after each use.
Periodically (and always with the machine off) it
is important to do all the cleaning of the machine,
removing glue residue that could affect the proper
functioning of the equipment. Clean the guides, the
axes and the main cutter carefully.
To maintain quality of the cutter, it is very important
to keep the scissors free of glue residue or tape. To
clean it, use a cloth with thinner or kerosene, gently
wipe the cutter, removing all the glue residue.
LUBRIFICATION
Once all bearings are shielded and have permanent
lubrication, just leave them like this until it is need
to be replaced. Do not lubricate them. For the other
items on this machine, an occasional application of
micro-electric machine oil is needed in the hinge that
moves the glue pot and manual cutter scissors.
Before lubricating, try cleaning the areas to be
lubricated, eliminating the accumulation of dirt.
MAINTENANCE
BRACKET
Due to transport and even during use, it may be that
the glue axis turn out of bracket.
The fact that the glue axis is out of bracket causes
incorrect application of glue in the wood paneling,
applying impartial glue or not even applying any glue
on the wood.
If the glue axis of your Edgebander is out of the
bracket, you can regulate it easily by following these
steps:
- Clean the glue axis, removing glue excess. For
this heat the machine until melt point of the glue,
facilitating the glue axis cleaning. Once the glue is
melted, turn off the machine, stopping the axis in
order to clean it and check the bracket.
- Support the side of a bracket on the table tabs,
leaning against the glue axis.
- If any point of the bracket face is not touching the
glue axis, you must do the following setting:
- If the top of the axis is tilted to the back of the
machine, loosen the Allen screws 5mm at point B (see
figure below) and press (about 1/4 turn) the hex bolts
also from the point B. Check the bracket again. If it is
corrected, tighten the Allen screws.
- If the top of the axis is tilted to the front of the
machine, loosen the Allen screws at point A and
tighten (about 1/4 turn) the hex screws. Check out
the bracket again. If it is corrected, tighten the Allen
screws; if not, repeat the procedure.
MAINTENANCE SCHEDULE
Daily:
• Aspirate all dust on top and around the machine.
• Clean the guides, rubberized axis and manual cutter,
freeing of all glue residue.
• Check the level of glue on the glue pot.
Weekly:
• Clean dust accumulation inside the back cover,
around the glue axis and glue pot of the machine.
• Check for wear or damage to the buttons and cord.