![background image](http://html1.mh-extra.com/html/makita/vr003g/vr003g_instruction-manual_4017163007.webp)
7 ENGLISH
Intended use
The tool is intended for removing bubbles from concrete
when casting concrete.
Noise
The typical A-weighted noise level determined accord-
ing to EN60745-2-12:
Model VR001G
Sound pressure level (L
pA
) : 80 dB (A)
Uncertainty (K) : 3 dB (A)
Model VR003G
Sound pressure level (L
pA
) : 80 dB(A)
Uncertainty (K) : 3 dB(A)
Model VR004G
Sound pressure level (L
pA
) : 80 dB(A)
Uncertainty (K) : 3 dB(A)
The noise level under working may exceed 80 dB (A).
NOTE:
The declared noise emission value(s) has
been measured in accordance with a standard test
method and may be used for comparing one tool with
another.
NOTE:
The declared noise emission value(s)
may also be used in a preliminary assessment of
exposure.
WARNING:
Wear ear protection.
WARNING:
The noise emission during actual
use of the power tool can differ from the declared
value(s) depending on the ways in which the
tool is used especially what kind of workpiece is
processed.
WARNING:
Be sure to identify safety mea-
sures to protect the operator that are based on an
estimation of exposure in the actual conditions of
use (taking account of all parts of the operating
cycle such as the times when the tool is switched
off and when it is running idle in addition to the
trigger time).
Vibration
The vibration total value (tri-axial vector sum) deter
-
mined according to EN60745-2-12:
Model VR001G
Work mode: load with flexible hose
Vibration emission (a
h
) : 4.9 m/s
2
Uncertainty (K) : 1.5 m/s
2
Model VR003G
Work mode: load with flexible hose
Vibration emission (a
h
) : 4.9 m/s
2
Uncertainty (K) : 1.5 m/s
2
Model VR004G
Work mode: load with flexible hose
Vibration emission (a
h
) : 4.9 m/s
2
Uncertainty (K) : 1.5 m/s
2
NOTE:
The declared vibration total value(s) has been
measured in accordance with a standard test method
and may be used for comparing one tool with another.
NOTE:
The declared vibration total value(s) may also
be used in a preliminary assessment of exposure.
WARNING:
The vibration emission during
actual use of the power tool can differ from the
declared value(s) depending on the ways in which
the tool is used especially what kind of workpiece
is processed.
WARNING:
Be sure to identify safety mea-
sures to protect the operator that are based on an
estimation of exposure in the actual conditions of
use (taking account of all parts of the operating
cycle such as the times when the tool is switched
off and when it is running idle in addition to the
trigger time).
Declarations of Conformity
For European countries only
The Declarations of conformity are included in Annex A
to this instruction manual.
SAFETY WARNINGS
General power tool safety warnings
WARNING
Read all safety warnings, instructions,
illustrations and specifications provided with this
power tool.
Failure to follow all instructions listed below
may result in electric shock, fire and/or serious injury.
Save all warnings and instruc-
tions for future reference.
The term "power tool" in the warnings refers to your
mains-operated (corded) power tool or battery-operated
(cordless) power tool.
Cordless concrete vibrator safety
warnings
1.
Always keep your hands and face away from
vibrating head when operating.
2.
Switch off the tool immediately if you notice abnor
-
mal noise or something faulty during operation.
3.
Inspect the tool carefully for breakage, cracks
or deformation if you accidentally drop it or
strike it against something.
4.
Do not carry the tool with finger on switch.
5.
Do not set the tool down and switch it on. The
vibrating head may whip around out of control
and cause an accident.
6.
Be careful not to allow water, wet concrete or
the like to get into the tool. Do not let the tool
fall into wet concrete.
7.
Insert the vibrating head carefully between
iron/steel frames or reinforcing rods not to
come in contact with them.
8.
Do not crush or twist the flexible hose.
9.
Do not overly bend the flexible hose.
10.
Use a wet cloth or the like to carefully wipe off
any wet concrete left on the tool after use. Extra
care should be given to thorough cleaning of
the vents, switch area, cover openings, etc.
Содержание VR003G
