![background image](http://html1.mh-extra.com/html/makita/vr003g/vr003g_instruction-manual_4017163011.webp)
11 ENGLISH
Mode selector
The speed (frequency) of vibrations can be changed in
two levels using the mode selector.
Press the mode button to toggle the vibrations in normal
mode (1) and power mode (2). Either of the two indica
-
tors for the mode you select lights up.
►
Fig.15:
1.
Normal mode indicator (1)
2.
Power
mode indicator (2)
3.
Mode button
Mode
(Indi-
cation
number)
Vibrations
per minute
Application
Normal
mode (1)
12,000 min
-1
For formwork and surface
vibrating operations;
Commonly used in precast con-
crete construction, small pours
that require a minimal amount of
vibration, patching and repairing
work with precise operation.
Power
mode (2)
15,500 min
-1
For vibrations at larger pours;
Ideal for pours with a greater sur-
face area, such as construction
joints, slab consolidation, where
the operator moves around to
cover the entire area.
NOTE:
The mode you select will be saved automat-
ically when the tool is powered off. The tool restarts
in the same mode as it previously used when turned
on again.
NOTE:
When the battery protection system works,
the mode indicators turn off.
NOTE:
When the remaining battery capacity
becomes low, either of the two indicators for the mode
you are currently using will blink. The timing, at which
the lamp starts blinking depends on the temperature
at work place and the battery cartridge conditions.
Accidental restart preventive
function
If you install the battery cartridge while pulling the
switch trigger, the tool does not start.
To start the tool, release the switch trigger, and then pull
the switch trigger again.
When the lock button is engaged, pull the switch trigger
fully and release it to exit the lock. Then pull the switch
trigger again.
Electronic function
The tool is equipped with the following electronic func-
tion for easy operation.
Constant speed control
Possible to perform a stable operation, because the
speed (frequency) of vibrations is kept constant even
under the loaded condition.
ASSEMBLY
CAUTION:
Always be sure that the tool is
switched off and the battery cartridge is removed
before carrying out any work on the tool.
Installing and removing flexible
shaft
Optional accessory
Installation
1.
Pull the flexible core shaft reasonably straight out
of the outer casing.
►
Fig.16:
1.
Flexible core shaft
2.
Outer casing
2.
Hold the drive shaft in the tool still using the
wrench provided. Then hand thread the end fitting of the
flexible core shaft onto the solid drive shaft in the tool.
►
Fig.17:
1.
Drive shaft
2.
End fitting
3.
Flexible core
shaft
3.
Fasten the end fitting of the flexible core shaft up
tightly using a pair of pliers.
►
Fig.18
4.
Hand thread the coupling of the outer casing onto
the male thread of the tool.
►
Fig.19:
1.
Coupling
2.
Outer casing
3.
Male thread
►
Fig.20:
1.
Outer casing
2.
Flexible core shaft
NOTE:
The coupling does not reach or fit securely
onto the male thread of the tool, when the top of the
flexible core shaft is not fit into the slot in the vibration
head. To fit them fully, pull the outer casing further
towards the tool while hand-turning the flexible core
shaft.
CAUTION:
Do not force the flexible core shaft
into the outer casing. Do not operate the tool with
the battery to fit the flexible shaft.
Such actions
may cause personal injury or damage to the flexible
core shaft.
5.
Knock each of the three corners of triangular
coupling with a hammer a few times in random order to
secure assembly.
►
Fig.21
Uninstallation
Follow the installation steps in reverse order.
Содержание VR003G
