![background image](http://html1.mh-extra.com/html/makita/tw004gz/tw004gz_instruction-manual_4289969009.webp)
9 ENGLISH
NOTE:
When none of the lamp on the panel is lit, pull the switch trigger once before pressing the button .
NOTE:
All lamps on the switch panel go out when the tool is turned off to save the battery power. The impact force
grade can be checked by pulling the switch trigger to the extent that the tool does not operate.
Changing the application mode
This tool employs several easy-to-use application modes for driving bolts with good control.
The type of the application mode changes every time you press the button
.
You can change the application mode within approximately one minute after releasing the switch trigger.
NOTE:
You can extend the time to change the application mode approximately one minute if you press the but
-
ton or .
►
Fig.8
Application mode
(Assist type displayed on panel)
Feature
Purpose
Bolt mode
Clockwise
This mode helps to repeat screwdriving continuously with
equal torque. This mode also helps to reduce the risk of
breakage of bolts/nuts due to overtightening.
Counterclockwise
This mode helps to prevent a bolt from falling off. When
loosening a bolt with the tool driving in counterclockwise
rotation, the tool automatically stops or slows down after
the bolt/nut gets enough loosened.
NOTE:
The timing to stop the driving varies depending on the
type of the bolt/nut and material to be driven. Make a
test driving before using this mode.
Clockwise
Preventing over
tightening of bolts.
Counterclockwise
Loosening bolts.
Bolt mode (1)
Clockwise
The tool stops automatically as soon as it has started
impact blows.
Counterclockwise
The impact force is 4. The tool stops automatically as soon
as it has stopped impact blows.
–
Bolt mode (2)
Clockwise
The tool stops automatically approximately 0.5 second later
from the moment that the tool has started impact blows.
Counterclockwise
The impact force is 4. The tool stops automatically approx
-
imately 0.2 second later from the moment that the tool has
stopped impact blows.
–
Bolt mode (3)
Clockwise
The tool stops automatically approximately 1 second later
from the moment that the tool has started impact blows.
Counterclockwise
The tool slows down the rotation after it has stopped impact
blows.
–
: The lamp is on.
NOTE:
When none of the lamp on the panel is lit, pull the switch trigger once before pressing the button .
NOTE:
All lamps on the switch panel go out when the tool is turned off to save the battery power. The type of the
application mode can be checked by pulling the switch trigger to the extent that the tool does not operate.
Full speed mode
►
Fig.9:
1.
Button
2.
Lamp
When full speed mode is turned on, the tool speed
becomes fastest even if you do not pull the switch trig
-
ger fully. When full speed mode is turned off, the tool
speed increases as you increase the pressure on the
switch trigger.
To turn on full speed mode, press and hold the but-
ton
. To turn off full speed mode, press and hold the
button again.
The lamp turns on while full speed mode is on.
NOTE:
Full speed mode continues even after switch-
ing the impact force mode/auto stop mode.
Содержание TW004GZ
