6 ENGLISH
Safety Warnings Specific for Polishing Operations
1 .
Do not allow any loose portion of the polishing
bonnet or its attachment strings to spin freely.
Tuck aw ay or trim any loose attachment strings.
L oose and spinning attac h ment strings c an entan-
gle your fingers or snag on the workpiece.
Additional Safety W arnings
1 .
Do not leave the tool running. Operate the tool
only w hen hand-held.
2.
Check that the w orkpiece is properly supported.
3.
If w orking place is extremely hot and humid, or
badly polluted by conductive dust, use a short-cir-
cuit breaker ( 30 mA) to assure operator safety.
4 .
Do not use the tool on any materials contain-
ing asbestos.
SAVE THESE INSTRUCTIONS.
WARNING:
DO NOT let comfort or familiarity
w ith product ( gained from repeated use) replace
strict adherence to safety rules for the subject
product. MISUSE or failure to follow the safety
rules stated in this instruction manual may cause
serious personal injury.
FUNCTIONAL
DESCRIPTION
CAUTION:
Alw ays be sure that the tool is
sw itched off and unplugged before adjusting or
checking function on the tool.
Sw itch action
CAUTION:
Before plugging in the tool, alw ays
check to see that the sw itch trigger actuates
properly and returns to the " OFF" position w hen
released.
Fig.1:
1.
S w itc h trigger
2.
L oc k button
T o start th e tool, simply pull th e sw itc h trigger. T h e
rotation speed w ill inc rease as y ou pull th e trigger.
R elease th e sw itc h trigger to stop. F or c ontinuous oper-
ation, pull th e sw itc h trigger, push in th e loc k button and
th en release th e sw itc h trigger. T o stop th e tool f rom th e
loc ked position, pull th e trigger f ully , th en release it.
CAUTION:
Sw itch can be locked in " ON" posi-
tion for ease of operator comfort during extended
use. Apply caution w hen locking tool in " ON"
position and maintain firm grasp on tool.
CAUTION:
Do not plug in the tool w ith the
lock-on sw itch engaged.
T h e tool w ill be run
unsupported and it may cause a personal injury or
breakage.
Speed adjusting dial
Fig.2:
1.
Speed adjusting dial
T h e rotating speed c an be c h anged by turning th e
speed adjusting dial to a given number setting from to
5 . H igh er speed is obtained w h en th e d ial is turned in
th e d irec tion of number 5 . A nd low er speed is obtained
w h en it is turned in th e d irec tion of number 1 .
R ef er to th e table f or th e relationsh ip betw een th e number
settings on th e d ial and th e approx imate rotating speed .
Number
Orbits per min.
Pad rotating
speed per minute
in random orbit
w ith forced rota-
tion mode
1
1 ,6 00
1 8 0
2
2,5 00
29 0
3
3,700
4 30
4
5 ,300
6 1 0
5
6 ,8 00
78 0
NOTICE:
If the tool is operated continuously
at low speeds for a long time, the motor w ill get
overloaded, resulting in tool malfunction.
NOTICE:
The speed adjusting dial can be turned
only as far as 5 and back to 1. Do not force it past
5 or 1, or the speed adjusting function may no
longer w ork.
Electronic function
T h e tools eq uipped w ith elec tronic f unc tion are easy to
operate bec ause of th e f ollow ing f eatures.
Constant speed control
Possible to get fine finish, because the rotating speed is
kept c onstant ev en und er th e load ed c ond ition.
Soft start feature
S of t start bec ause of suppressed starting sh oc k.
Selecting the action mode
T urn th e c h ange knob to alter th e rotation mod e.
Fig.3:
1.
C h ange knob
NOTICE:
Alw ays turn the knob fully. If the knob
is in the middle position, you cannot turn on the
tool.
NOTICE:
You cannot change the action mode
w hen the tool is sw itched on.
Random orbit w ith forced rotation
mode
Fig.4:
1.
C h ange knob
R and om orbit w ith f orc ed rotation mod e is orbital ac tion
w ith f orc ed rotation of th e pad f or rough polish ing suc h
as surf ac e treatment.
R otate th e c h ange knob c ounterc loc kw ise f or rand om
orbit w ith f orc ed rotation mod e.
