![background image](http://html1.mh-extra.com/html/makita/ls1018-r/ls1018-r_instruction-manual_4276320015.webp)
15
confuse the operator as to the actual blade path
while cutting and contact with the blade will result in
serious personal injury.
•
The blade should not be raised until it has
come to a complete stop.
During a bevel cut the
piece cut off may come to rest against the blade. If
the blade is raised while it is rotating the cut-off
piece maybe ejected by the blade causing the
material to fragment which may result in serious
personal injury.
NOTICE:
•
When pressing down the handle, apply pressure in
parallel with the blade. If a force is applied
perpendicularly to the turn base or if the pressure
direction is changed during a cut, the precision of
the cut will be impaired.
•
Before bevel-cutting, an adjustment of the upper
fence and lower fence maybe required. Refer to
the section titled "Guide fence adjustment".
CAUTION:
•
Always remove the sub-fence R so that it does not
interfere any part of the carriage when performing
right bevel cuts.
5. Compound
cutting
Compound cutting is the process in which a bevel
angle is made at the same time in which a miter
angle is being cut on a workpiece. Compound
cutting can be performed at the angle shown in the
table.
Miter angle
Bevel angle
Left and Right 0 - 45
Left and Right 0 - 45
009713
When performing compound cutting, refer to "Press
cutting", "Slide cutting", "Miter cutting" and "Bevel
cut" explanations.
6.
Cutting crown and cove moldings
Crown and cove moldings can be cut on a
compound miter saw with the moldings laid flat on
the turn base.
There are two common types of crown moldings
and one type of cove moldings; 52/38° wall angle
crown molding, 45° wall angle crown molding and
45° wall angle cove molding. See illustrations.
1
2
3
001555
There are crown and cove molding joints which are
made to fit "Inside" 90° corners ((1) and (2) in Fig.
A) and "Outside" 90° corners ((3) and (4) in Fig. A).
(1) (2) (3) (4)
1
2
Fig.A
001556
2
(1)
(2)
(1)
(2)
(2)
(1)
(2)
(1)
(1)
(2)
(3)
(4)
1
001557
Measuring
Measure the wall length and adjust workpiece on
table to cut wall contact edge to desired length.
Always make sure that cut workpiece length
at the
back of the workpiece
is the same as wall length.
Adjust cut length for angle of cut. Always use several
pieces for test cuts to check the saw angles.
When cutting crown and cove moldings, set the
bevel angle and miter angle as indicated in the table
(A) and position the moldings on the top surface of
the saw base as indicated in the table (B).
In the case of left bevel cut
M
ol
d
i
ng
posi
t
io
n
i
n
Fi
g
. A
Beve
l
ang
l
e
M
i
ter
ang
l
e
Fo
r
ou
t
si
de
co
rner
Fo
r
i
n
si
de
co
rner
5
2/38°
t
yp
e
4
5
°
t
yp
e
R
i
ght
3
1
.6°
4
5
°
t
yp
e
L
eft
33.9°
L
eft
3
0
°
5
2/38°
t
yp
e
L
eft
3
1
.6°
L
eft
3
5
.3°
R
i
ght
3
5
.3°
R
i
ght
3
5
.3°
R
i
ght
3
1
.6°
(
1
)
(2)
(3)
(4)
T
a
bl
e
(A)
006361
1. Inside corner
2. Outside corner
1. Inside corner
2. Outside corner
1. 52/38
゚
type
crown molding
2. 45
゚
type crown
molding
3. 45
゚
type cove
molding
Содержание LS1018-R
Страница 71: ...71 ...