Makita LS1018-R, Инструкция по эксплуатации

Страница: 16 / 72

16
M ol d i ng
posi t io n i n
Fi g . A
M ol d i ng edge aga i n s t
g ui de fen c e
( 1 )
C e ili ng co nta c t edge s h oul d
b e aga i n s t g ui de fen c e .
C e ili ng co nta c t edge s h oul d
b e aga i n s t g ui de fen c e .
Fo r
ou t si de
co rner
Fi n is hed pi e c e
will b e o n the
L eft si de o f
bl ade .
Fi n is hed pi e c e
will b e o n the
R i ght si de o f
bl ade .
Fo r i n si de
co rner
W a ll co nta c t edge s h oul d b e
aga i n s t g ui de fen c e .
Fi n is hed pi e c e
(2)
(3)
(4)
T a bl e ( B )
006362
Example:
In the case of cutting 52/38° type crown
molding for position (1) in Fig. A:
•
Tilt and secure bevel angle setting to
33.9° LEFT.
•
Adjust and secure miter angle setting to
31.6° RIGHT.
•
Lay crown molding with its broad back
(hidden) surface down on the turn base
with its CEILING CONTACT EDGE
against the guide fence on the saw.
•
The finished piece to be used will
always be on the LEFT side of the blade
after the cut has been made.
In the case of right bevel cut
M ol d i ng
posi t io n i n
Fi g . A
Beve l ang l e M i ter ang l e
Fo r ou t si de
co rner
Fo r i n si de
co rner
5 2/38° t yp e 4 5 ° t yp e
R i ght 3 1 .6°
4 5 ° t yp e
R i ght 33.9° R i ght 3 0 °
5 2/38° t yp e
L eft 3 1 .6° L eft 3 5 .3°
R i ght 3 5 .3°
R i ght 3 5 .3° R i ght 3 1 .6°
( 1 )
(2)
(3)
(4)
T a bl e (A)
006363
M ol d i ng
posi t io n i n
Fi g . A
M ol d i ng edge aga i n s t
g ui de fen c e
( 1 )
Fo r
ou t si de
co rner
Fo r i n si de
co rner
Fi n is hed pi e c e
(2)
(3)
(4)
T a bl e ( B )
Fi n is hed pi e c e
will b e o n the
L eft si de o f
bl ade .
Fi n is hed pi e c e
will b e o n the
R i ght si de o f
bl ade .
W a ll co nta c t edge s h oul d b e
aga i n s t g ui de fen c e .
W a ll co nta c t edge s h oul d b e
aga i n s t g ui de fen c e .
C e ili ng co nta c t edge s h oul d
b e aga i n s t g ui de fen c e .
006364
Example:
In the case of cutting 52/38° type crown
molding for position (1) in Fig. A:
•
Tilt and secure bevel angle setting to
33.9° RIGHT.
•
Adjust and secure miter angle setting to
31.6° RIGHT.
•
Lay crown molding with its broad back
(hidden) surface down on the turn base
with its WALL CONTACT EDGE against
the guide fence on the saw.
•
The finished piece to be used will
always be on the RIGHT side of the
blade after the cut has been made.