![background image](http://html1.mh-extra.com/html/makita/ls0714f/ls0714f_instruction-manual_4026500019.webp)
19
Adjusting the position of laser line (Fig. 49 & 50)
For model LS0714FL, LS0714L
WARNING:
• As the tool is plugged when adjusting the position of
laser line, take a full caution especially at switch action.
Pulling the switch trigger accidentally cause an acci-
dental start of the tool and personal injury.
CAUTION:
• Never look into the laser beam directly. Direct laser
beam causes damage to your eyes.
• Never apply a blow or impact to the tool. A blow or
impact causes the incorrect position of laser line, dam-
age to the laser beam emitting part or a short life of the
tool.
When adjusting the laser line appears on the left side
of the saw blade
1
Screw to change the movable range of the adjusting
screw
2
Adjusting screw
3
Hex wrench
4
Laser line
5
Saw blade
When adjusting the laser line appears on the right
side of the saw blade
1
Screw to change the movable range of the adjusting
screw
2
Saw blade
3
Laser line
For both adjustments, do as follows.
1.
Make sure that the tool is unplugged.
2.
Draw the cutting line on the workpiece and place it
on the turn table. At this time, do not secure the
workpiece with a vise or similar securing device.
3.
Lower the blade by lowering the handle and just
check to see where the cutting line and the position
of the saw blade is. (Decide which position to cut on
the line of cut.)
4.
After decision the position to be cut, return the han-
dle to the original position. Secure the workpiece
with the vertical vise without shifting the workpiece
from the pre-checked position.
5.
Plug the tool and turn on the laser switch.
6.
Adjust the position of laser line as follows.
The position of laser line can be changed as the movable
range of the adjusting screw for the laser is changed by
turning two screws with a hex wrench. (The movable
range of laser line is factory adjusted within 1 mm from
the side surface of blade.)
To shift the laser line movable range further away from
the side surface of blade, turn the two screws counter-
clockwise after loosening the adjusting screw. Turn these
two screws clockwise to shift it closer to the side surface
of the blade after loosening the adjusting screw.
Refer to the section titled “Laser beam action” and adjust
the adjusting screw so that the cutting line on your work-
piece is aligned with the laser line.
NOTE:
• Check the position of laser line regularly for accuracy .
• Have the tool repaired by Makita authorized service
center for any failure on the laser unit.
Replacing fluorescent tube (Fig. 51)
For model LS0714F, LS0714FL
CAUTION:
• Always be sure that the tool is switched off and
unplugged before replacing the fluorescent tube.
• Do not apply force, impact or scratch to a fluorescent
tube, which can cause a glass of the fluorescent tube to
be broken resulting in a injury to you or your bystand-
ers.
• Leave the florescent tube for a while immediately after
a use of it and then replace it. If not, you may burn
yourself.
Remove screws, which secure Lamp Box for the light.
Pull out the Lamp Box keeping pushing lightly the upper
position of it as shown in the figure.
Pull out the fluorescent tube and then replace it with
Makita original new one.
Cleaning of the lens for the laser light
(Fig. 52 & 53)
For model LS0714FL, LS0714L
If the lens for the laser light becomes dirty, or sawdust
adheres to it in such a way that the laser line is no longer
easily visible, unplug the saw and remove and clean the
lens for the laser light carefully with a damp, soft cloth.
Do not use solvents or any petroleum-based cleaners on
the lens.
To remove the lens for the laser light, remove the saw
blade before removing the lens according to the instruc-
tions in the section titled “Installing or removing saw
blade”.
Loosen but do not remove the screw which secures the
lens using a screwdriver.
Pull out the lens as shown in the figure.
NOTE:
• If the lens does not come out, loosen the screw further
and pull out the lens again without removing the screw.
Replacing carbon brushes (Fig. 54 & 55)
Remove and check the carbon brushes regularly.
Replace when they wear down to the limit mark. Keep
the carbon brushes clean and free to slip in the holders.
Both carbon brushes should be replaced at the same
time. Use only identical carbon brushes.
Use a screwdriver to remove the brush holder caps. Take
out the worn carbon brushes, insert the new ones and
secure the brush holder caps.
1
2
3
4
5
1
2
3
Содержание LS0714F
