6
FUNCTIONAL DESCRIPTION
CAUTION:
•
Always be sure that the tool is switched off and
unplugged before adjusting or checking function
on the tool.
Depth adjustment
For model FS4000, FS4200, FS4300, FS4300A,
FS6200, FS6300, FS6300A, FS6300R
Fig.1
The depth can be adjusted by turning the lock ring. Turn
it in "B" direction for less depth and in "A" direction for
more depth. One full turn of the lock ring equals 2.0 mm
change in depth.
For model FS4000X, FS4300X, FS6300X
Fig.2
The depth can be adjusted by turning the locking sleeve.
Turn it in "A" direction for less depth and in "B" direction
for more depth. One full turn of the locking sleeve
equals 1.5 mm change in depth.
For all Models
Adjust the lock ring so that the distance between the tip
of the locator and the screw head is approximately 1
mm as shown in the figures. Drive a trial screw into your
material or a piece of duplicate material. If the depth is
still not suitable for the screw, continue adjusting until
you obtain the proper depth setting.
Fig.3
Fig.4
Switch action
Fig.5
CAUTION:
•
Before plugging in the tool, always check to see
that the switch trigger actuates properly and
returns to the "OFF" position when released.
To start the tool, simply pull the switch trigger. Tool
speed is increased by increasing pressure on the switch
trigger. Release the switch trigger to stop.
For continuous operation, pull the switch trigger and
then push in the lock button.
To stop the tool from the locked position, pull the switch
trigger fully, then release it.
NOTE:
•
Even with the switch on and motor running, the bit
will not rotate until you fit the point of the bit in the
screw head and apply forward pressure to engage
the clutch.
Lighting up the lamps
For model
FS4200,FS4300,FS4300A,FS4300X,FS6200,FS6300,
FS6300A,FS6300R,FS6300X
Fig.6
CAUTION:
•
Do not look in the light or see the source of light
directly.
To turn on the lamp, pull the trigger. Release the trigger
to turn it off.
NOTE:
•
Use a dry cloth to wipe the dirt off the lens of lamp.
Be careful not to scratch the lens of lamp, or it
may lower the illumination.
Reversing switch action
Fig.7
CAUTION:
•
Always check the direction of rotation before operation.
•
Use the reversing switch only after the tool comes
to a complete stop. Changing the direction of
rotation before the tool stops may damage the tool.
This tool has a reversing switch to change the direction
of rotation. Move the reversing switch lever to
the
position (A side) for clockwise rotation or
the
position (B side) for counterclockwise rotation.
Hook
Fig.8
The hook is convenient for temporarily hanging the tool.
ASSEMBLY
CAUTION:
•
Always be sure that the tool is switched off and
unplugged before carrying out any work on the tool.
Installing or removing the bit
For model FS4000, FS4200, FS4300, FS4300A,
FS6200, FS6300, FS6300A, FS6300R
To remove the bit, first remove the locator by pulling the
lock ring away from the gear housing.
Fig.9
Grasp the bit with a pair of pliers and pull the bit out of
the magnetic bit holder. Sometimes, it helps to wiggle
the bit with the pliers as you pull.
To install the bit, push it firmly into the magnetic bit
holder. Then install the locator by pushing it firmly back
onto the gear housing.
Fig.10
For model FS4000X, FS4300X, FS6300X
To remove the bit, first pull the locator out of the locking
sleeve. Then grasp the bit with a pair of pliers and pull
the bit out of the magnetic bit holder. Sometimes, it
helps to wiggle the bit with the pliers as you pull.
