background image

6 ENGLISH

Operation

1. 

Always use two hands to operate the tool fitted 

with two handles.

 Using one hand could cause 

loss of control and result in serious personal injury.

2. 

While operating the tool, always ensure that 

the operating position is safe and secure. 

Overreaching with the tool, particularly from 

a ladder, is extremely dangerous. Do not work 

from anything wobbly or infirm.

3. 

Do not simultaneously wear multiple belt har-

nesses and/or shoulder harnesses when oper-

ating the tool.

4. 

During operation, keep bystanders or animals 

at least 15 m away from the tool. Stop the tool 

as soon as someone approaches.

5. 

If cutting tool strikes any object or the tool 

starts making unusual noise or vibration, 

switch off the tool and remove the battery car

-

tridge immediately and allow the tool to stop. 

And then take the following steps:

• 

inspect for damage

• 

check for, and tighten, any loose parts

• 

have any damaged parts replaced or 

repaired with genuine spare parts.

6. 

Only use the tool for its intended purpose. Do 

not use the tool for any other purpose.

7. 

Switch off the tool and remove the battery 

cartridge before:

• 

cleaning or when clearing a blockage,

• 

checking, carrying out maintenance or 

working on the tool,

• 

adjusting the working position of the 

shear blades,

• 

leaving the tool unattended.

8. 

Ensure that the tool is correctly located in a 

designated working position before starting 

the tool.

9. 

Do not operate the tool with a damaged or 

excessively worn shear blades.

10. 

Always ensure that all handles and guards 

are fitted when using the tool. Never attempt 

to use an incomplete tool or one fitted with an 

unauthorized modification.

11. 

Always be aware of your surroundings and 

stay alert for possible hazards of which you 

may not be aware due to the noise of the tool.

12. 

Be careful not to accidentally contact a metal 

fence or other hard objects during operation.

 

The blade will break and may cause serious injury.

13. 

Avoid unintentional starting. Do not carry the 

tool when the battery cartridge is installed 

and with finger on the switch. Make sure that 

the switch is off when installing the battery 

cartridge.

14. 

Do not grasp the exposed cutting blades or 

cutting edges when picking up or holding the 

tool.

15. 

Do not force the tool.

 It will do the job better and 

with less likelihood of a risk of injury at the rate for 

which it was designed.

16. 

Do not use the tool in the rain or in wet or 

very damp conditions.

 The electric motor is not 

waterproof.

17. 

Hold the tool firmly when using the tool.

18. 

Do not operate the tool at no-load 

unnecessarily.

19. 

Before checking the shear blades, taking care 

of faults, or removing foreign objects caught 

in the shear blades, always switch off the tool 

and remove the battery cartridge.

20. 

Never point the shear blades to yourself or 

others.

21. 

If the blades stop moving due to the stuck of 

foreign objects between the blades during 

operation, switch off the tool and remove the 

battery cartridge, and then remove the foreign 

objects using tools such as pliers.

 Removing 

the foreign objects by hand may cause an injury 

for the reason that the blades may move in reac

-

tion to removing the foreign objects.

Maintenance and storage

1. 

When the tool is stopped for servicing, inspec-

tion or storage, switch off the tool and remove 

the battery cartridge, and make sure all mov-

ing parts have come to a stop. Allow the tool 

to cool before making any inspections, adjust-

ment, etc.

2. 

Always allow the tool to cool down before 

storing.

3. 

When not in use, attach the blade cover to the 

tool and store the tool indoors in dry, and high 

locked-up place, out of reach of children.

4. 

Maintain the tool with care. Keep cutting edge 

sharp and clean for best performance and to 

reduce the risk of injury. Follow instructions 

for lubricating and changing accessories. 

Keep handles dry, clean, and free from oil and 

grease.

5. 

Check damaged parts. Before further use of 

the tool, any part which is damaged should be 

carefully checked to determine that it will oper-

ate properly and perform its intended function. 

Check for alignment of moving parts, binding 

of moving parts, breakage of parts, mounting 

and any other condition that may affect its 

operation.

 A guard or other part that is damaged 

should be properly repaired or replaced by your 

authorized service center.

6. 

Use genuine spare parts only.

7. 

When moving the tool to another location, 

including during work, always remove the 

battery cartridge and put the blade cover on 

the shear blades. Never carry or transport the 

tool with the blades running. Never grasp the 

blades with your hands.

8. 

Clean the tool and especially the shear blades 

after use, and before putting the tool into stor-

age for extended periods. Lightly oil the shear 

blades and put on the blade cover.

9. 

Do not dispose of the battery(ies) in a fire. The 

cell may explode. Check with local codes for 

possible special disposal instructions.

10. 

Do not open or mutilate the battery(ies). 

Released electrolyte is corrosive and may 

cause damage to the eyes or skin. It may be 

toxic if swallowed.

Содержание DUN500WRTE





















Отзывы: