background image

2 ENGLISH

SPECIFICATIONS

Model:

DUH506

DUH606

Blade length

500 mm

600 mm

Strokes per minute

4,000 min

-1

Overall length

(Without battery)

846 mm

965 mm

Rated voltage

D.C. 18 V

Net weight

2.5 - 2.9 kg

2.7 - 3.0 kg

• 

Due to our continuing program of research and development, the specifications herein are subject to change 

without notice.

• 

Specifications may differ from country to country.

• 

The weight may differ depending on the attachment(s), including the battery cartridge. The lightest and heavi

-

est combination, according to EPTA-Procedure 01/2014, are shown in the table.

Applicable battery cartridge and charger

Battery cartridge

BL1815N / BL1820B / BL1830B / BL1840B / BL1850B / BL1860B

Charger

DC18RC / DC18RD / DC18RE / DC18SD / DC18SE / DC18SF / 

DC18SH / DC18WC

 

Some of the battery cartridges and chargers listed above may not be available depending on your region of 

residence.

WARNING:

 

Only use the battery cartridges and chargers listed above.

 Use of any other battery cartridges 

and chargers may cause injury and/or fire.

Recommended cord connected power source

Portable power pack

PDC01

 

The cord connected power source(s) listed above may not be available depending on your region of residence.

 

Before using the cord connected power source, read instruction and cautionary markings on them.

Symbols

The followings show the symbols which may be used 

for the equipment. Be sure that you understand their 

meaning before use.

 

Read instruction manual.

Wear eye protection.

DANGER - Keep hands away from blade.

Do not expose to moisture.

 

Ni-MH

Li-ion

Only for EU countries

Due to the presence of hazardous com-

ponents in the equipment, waste electrical 

and electronic equipment, accumulators 

and batteries may have a negative impact 

on the environment and human health.

Do not dispose of electrical and electronic 

appliances or batteries with household 

waste!

In accordance with the European Directive 

on waste electrical and electronic equip-

ment and on accumulators and batteries 

and waste accumulators and batteries, 

as well as their adaptation to national law, 

waste electrical equipment, batteries and 

accumulators should be stored separately 

and delivered to a separate collection point 

for municipal waste, operating in accor-

dance with the regulations on environmen-

tal protection.

This is indicated by the symbol of the 

crossed-out wheeled bin placed on the 

equipment.
Guaranteed sound power level according 

to EU Outdoor Noise Directive.

Sound power level according to Australia 

NSW Noise Control Regulation.

Intended use

The tool is intended for trimming hedges.

Содержание DUH606


















Отзывы: