background image

12 ENGLISH

2.

  Hook the claws of the chip receiver to the groove 

on the shear blades.

1

2

Fig.19

►    

1.

 Claw 

2.

 Groove

3.

  Press the levers on the chip receiver, and then hook the 

claws on the other side to the groove on the shear blades.

1

Fig.20

►    

1.

 Lever

To remove the chip receiver, press the levers to release 

the claws.

1

Fig.21

►    

1.

 Lever

NOTICE:

 

Never try to remove the chip receiver 

by an excessive force with its hooks locked to the 

shear blades.

OPERATION

WARNING:

 

Keep hands away from shear blades.

CAUTION:

 

Avoid operating the tool in very 

hot weather as much as practicable. When operat-

ing the tool, be careful of your physical condition.

CAUTION:

 

Be careful not to accidentally con-

tact a metal fence or other hard objects while trim-

ming.

 The shear blades may break and cause an injury.

CAUTION:

 

Be careful not to allow the shear blades 

to contact the ground.

 The tool may recoil and cause an injury.

CAUTION:

 

Overreaching with a hedge trimmer, 

particularly from a ladder, is extremely dangerous.

 

Do not work while standing on anything wobbly or infirm.

NOTICE:

 

Do not attempt to cut branches thicker 

than 10 mm in diameter with the tool.

 Cut branches 

to 10 cm lower than the cutting height using branch 

cutters before using the tool.

(1)

(2)

Fig.22

►    

(1)

 Cutting height 

(2)

 10 cm

NOTICE:

 

Do not cut down dead trees or similar 

hard objects.

 Doing so may damage the tool.

NOTICE:

 

Do not trim the grass or weeds while 

using the shear blades.

 The shear blades may 

become tangled in the grass or weeds.

Hold the tool with both hands, hold the front handle 

while pressing the switch lever and pull the switch trig-

ger, and then move the tool forward.

Fig.23

Содержание DUH606


















Отзывы: