10 ENGLISH
ENGLISH (Original instructions)
SPECIFICATIONS
Model
DLS713
Blade diameter
190 mm
Hole (arbor) diameter (country specific)
20 mm or 15.88 mm
Max. kerf thickness of the saw blade
2.2 mm
Max. Miter angle
Left 47° , Right 57°
Max. Bevel angle
Left 45°, Right 5°
No load speed
2200 min
-1
Dimensions (L x W x H)
655 mm x 430 mm x 454 mm
Net weight
12.2 - 14.3 kg
Rated voltage
D.C. 18 V
•
Due to our continuing program of research and development, the specifications herein are subject to change
without notice.
•
Specifications may differ from country to country.
•
The weight may differ depending on the attachment(s), including the battery cartridge. The lightest and heavi-
est combination, according to EPTA-Procedure 01/2014, are shown in the table.
Applicable battery cartridge and charger
Battery cartridge
BL1815N / BL1820 / BL1820B / BL1830 / BL1830B / BL1840 /
BL1840B / BL1850 / BL1850B / BL1860B
Charger
DC18RC / DC18RD / DC18RE / DC18SD / DC18SE / DC18SF
•
Some of the battery cartridges and chargers listed above may not be available depending on your region of
residence.
WARNING:
Only use the battery cartridges and chargers listed above.
Use of any other battery cartridges
and chargers may cause injury and/or fire.
Max. Cutting capacities (H x W) with blade 190 mm in diameter.
Miter angle
Bevel angle
45° (left)
0°
5° (right)
0°
25 mm x 300 mm
52 mm x 300 mm
40 mm x 300 mm
-----
* 60 mm x 265 mm (Note 1)
-----
45° (left and right)
25 mm x 212 mm
52 mm x 212 mm
-----
-----
* 60 mm x 185 mm (Note 2)
-----
57° (right)
-----
52 mm x 163 mm
-----
-----
* 60 mm x 145 mm (Note 3)
-----
(Note)
* mark indicates that a wood facing with the following thickness is used.
1: When using a wood facing 20 mm thickness
2: When using a wood facing 15 mm thickness
3: When using a wood facing 10 mm thickness
Symbols
The followings show the symbols used for the equip-
ment. Be sure that you understand their meaning before
use.
Read instruction manual.
To avoid injury from flying debris, keep
holding the saw head down, after making
cuts, until the blade has come to a com-
plete stop.
When performing slide cut, first pull car
-
riage fully and press down handle, then
push carriage toward the guide fence.
Do not place hand or fingers close to the
blade.
Always set SUB-FENCE to left position
when performing left bevel cuts. Failure to
do so may cause serious injury to operator.
Содержание DLS713
