![background image](http://html1.mh-extra.com/html/makita/bjs160/bjs160_instruction-manual_4229529006.webp)
6
Check the smaller clearance with the thickness gauge
and adjust it.
When using the thickness gauge to adjust the blade
clearance, refer to the table.
After adjusting the clearance, tighten the screw securely.
Storing hex wrench (Fig. 6)
Store the hex wrench as shown in the figure when not in
use.
OPERATION
Lubrication (Fig. 7)
Before operation, lubricate the contact point of the center
blade and the pin. To keep good cutting performance, also
use a cutting lubricant from time to time during operation.
OPERATION (Fig. 8)
Turn the tool on and set front ends of the side blades on
the workpiece. Now simply move the tool forward,
keeping the side blades flush with the workpiece surface.
(Fig. 9)
CAUTION:
• When cutting a small portion of the workpiece, you may
have difficulty completing the end of the cut. In that
case, try to cut it again, pulling the workpiece back
slightly.
MAINTENANCE
CAUTION:
• Always be sure that the tool is switched off and the
battery cartridge is removed before attempting to
perform inspection or maintenance.
NOTICE:
• Never use gasoline, benzine, thinner, alcohol or the
like. Discoloration, deformation or cracks may result.
The tool and its air vents have to be kept clean. Regularly
clean the tool’s air vents or whenever the vents start to
become obstructed.
Replacing carbon brushes (Fig. 10)
Remove and check the carbon brushes regularly. Replace
when they wear down to the limit mark. Keep the carbon
brushes clean and free to slip in the holders. Both carbon
brushes should be replaced at the same time. Use only
identical carbon brushes.
Insert the top end of slotted bit screwdriver into the notch
in the tool and remove the holder cap cover by lifting it up.
(Fig. 11)
Use a screwdriver to remove the brush holder caps. Take
out the worn carbon brushes, insert the new ones and
secure the brush holder caps.
(Fig. 12)
Reinstall the holder cap cover on the tool.
Replacing blades
The service life of the blades varies in terms of the
workpiece to be cut. The following reference tables
indicate the approximate service life of the blades.
When the blades become dull, ask Makita Authorized
Service Centers to replace the blades.
For BJS160 and BJS161
For BJS100 and BJS101
To maintain product SAFETY and RELIABILITY, repairs,
any other maintenance or adjustment should be
performed by Makita Authorized Service Centers, always
using Makita replacement parts.
ACCESSORIES
CAUTION:
• These accessories or attachments are recommended
for use with your Makita tool specified in this manual.
The use of any other accessories or attachments might
present a risk of injury to persons. Only use accessory
or attachment for its stated purpose.
If you need any assistance for more details regarding
these accessories, ask your local Makita Service Center.
• Thickness gauge
• Center blade
• Side blade R
• Side blade L
• Hex wrench
• Various type of Makita genuine batteries and chargers
For Model BJS160
For European countries only
ENG104-1
Noise
The typical A-weighted noise level determined according
to EN60745:
Sound pressure level (L
pA
): 74 dB (A)
Uncertainty (K): 3 dB (A)
The noise level under working may exceed 80 dB (A).
Wear ear protection.
Vibration
ENG218-2
The vibration total value (tri-axial vector sum) determined
according to EN60745:
Work mode: cutting sheet metal
Vibration emission (a
h
): 12.0 m/s
2
Uncertainty (K): 1.5 m/s
2
Workpiece thickness
(mm)
Marking on thickness
gauge
Less than 0.8
0.5
0.8 - 1.3
1.0
More than 1.3
1.5
Material
Cutting thickness
(mm)
Life of blades
(m)
Mild steel plate
(SPCC)
1.6
200
Stainless steel
plate
(SUS304)
1.2
150
Aluminum plate
(A-5052)
2.5
400
Material
Cutting thickness
(mm)
Life of blades
(m)
Mild steel plate
(SPCC)
1.0
120
Stainless steel
plate
(SUS304)
0.7
50
Содержание BJS160
