![background image](http://html.mh-extra.com/html/makita/4304t/4304t_instruction-manual_230036008.webp)
8
For 4305T (Fig. 4 & 5)
1.
Press the button to raise the blade installing
knob.
2.
Rotate the blade installing knob in the (B) direc-
tion and the clamp on the blade holder will open.
Open the clamp a little more than the thickness
of the blade to be installed.
3.
With the blade teeth facing forward, insert the
blade into the blade holder as far as it will go.
Make sure that the back edge of the blade fits
properly into the groove of the roller.
4.
With the blade held against the blade holder,
rotate the blade installing knob in the (D) direc-
tion to tighten the clamp.
5.
With the blade installing knob kept in this posi-
tion, push it back down to its original position.
NOTE:
Occasionally lubricate the roller.
Selecting action (Fig. 6)
This tool can be operated with an orbital or a straight line cutting action. To change the cutting action, just turn
the lever to the desired cutting action position. Refer to the table below to help determine the appropriate cut-
ting action.
Switch action for 4304T (Fig. 7)
CAUTION:
Before plugging in the tool, always check to see that
the switch trigger actuates properly and returns to the
“OFF” position when released.
To start the tool, simply pull the trigger. Release the
trigger to stop. For continuous operation, pull the trig-
ger and move the lock lever backward. To stop the
tool from the locked position, pull the trigger fully,
then release it.
For 4305T (Fig. 8)
CAUTION:
Before plugging in the tool, always check to see that
the switch actuates properly.
To start the tool, slide the switch lever forward. Slide
the switch lever backward to stop.
Speed adjusting dial (Fig. 9 & 10)
The tool speed can be adjusted and maintained
between 500 and 3,000 strokes per minute by turning
the adjusting dial. The dial is marked 1 (lowest
speed) to 6 (full speed).
Refer to the table right to select the proper speed for
the workpiece to be cut. However, the appropriate
speed may differ with the type or thickness of the
workpiece. In general, higher speeds will allow you to
cut workpieces faster but the service file of the blade
will be reduced.
CAUTION:
Adjust the speed adjusting dial only within the range
of numbers 1 through 6. Do not force the dial beyond
this range or damage to the tool may result.
Cutting operation (Fig. 11)
CAUTION:
• Always hold the tool with the base flush with the
workpiece. Failure to do so may cause a slanted
cutting surface and blade breakage.
• Advance the tool very slowly when cutting curves or
scrolling. Fording the tool may cause a slanted cut-
ting surface and blade breakage.
Turn the tool on without the blade making any con-
tact. Rest the base flat on the workpiece and gently
move the tool forward along the previously marked
cutting line.
Position
Cutting action
Applications
0
Straight line cutting action
For cutting mild steel, stainless steel and plastics.
For clean cuts in wood and plywood.
I
Small orbit cutting action
For cutting mild steel, aluminum and hard wood.
II
Medium orbit cutting action
For cutting wood and plywood.
For fast cutting in aluminum and mild steel.
III
Large orbit cutting action
For fast cutting in wood and plywood.
Workpiece to be cut
Number on
adjusting dial
Wood
5 – 6
Mild steel
3 – 6
Stainless steel
3 – 4
Aluminum
2 – 3
Plastics
1 – 4
Содержание 4304T
