manualshive.com logo in svg

Majestic Rio Case 2, Руководство по размерам и установке

Поделиться
Скачать
Majestic Rio Case 2 Скачать руководство пользователя страница 5

The Majestic Shower Company Limited

Two North Place, Edinburgh Way, Harlow, Essex CM20 2SL England

Tel44 (0) 8448 001 500

Fac44 (0) 1279 635 074  [email protected]  www.majesticshowers.com

5

5

6

Using suction glass lifters, lift the glass In Line panel into the vertical wall profile and gently
lower it into the Underframe channel. The Underframe Insert is supplied cut to the correct 
length., which is equal to the width of the glass Door plus 8 mm clearance for vertical seals.

Position the In Line panel so that the Underframe Insert fits snugly between the panel and 
the wall.

Use a spirit level to ensure that the edge of the panel is plumb vertical. If necessary, insert
additional rubber strips under the panel (a maximum of 3 thicknesses) to achieve this and
note the position of the rubber.

Mark the position of the edge of the In Line panel with tape on the underframe so
that it can be removed and replaced in the same position.

Mark the vertical wall profile at the top edge of the glass for trimming if it is too
long.

Rio Installation Guide - Surface Profiles

Door width + 8 mm

Содержание Rio Case 2
















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды