Majestic Rio Case 2 Скачать руководство пользователя страница 11

Страница: 11 / 15

The Majestic Shower Company Limited

Two North Place, Edinburgh Way, Harlow, Essex CM20 2SL England

Tel44 (0) 8448 001 500

Fac44 (0) 1279 635 074 [email protected] www.majesticshowers.com

above below and between the hinges.

For maximum resistance to leakage, the seal sections should be cut as shown above to allow
them to fill the gaps in the hinge through which water might otherwise escape.

The Glass to Glass vertical seal is to be cut in 3 sections to fit to the edge of the In Line panel

Rio Installation Guide - Surface Profiles

Open the door and slide the 3 sections of seal on to the edge of the glass panel,
pushing the notched ends inside the hinge as shown.

The lower section of the seal should be cut straight and pushed down to touch
the Underframe (see illustration at Step 19).

Slit here

12.5mm

VIEW FROM

INSIDE OF

ENCLOSURE

(OUTWARD

OPENING

DOOR)

GLASS NOT

SHOWN

Slit

Notch

Slit

Notch

DOOR SIDE

PANEL SIDE

Содержание Rio Case 2
















Результаты поиска

Содержание Rio Case 2

Отзывы:

Бренды по названию

Популярные бренды

Majestic Rio Case 2, Руководство по размерам и установке

Результаты поиска

Содержание Rio Case 2

Отзывы:

Бренды по названию

Популярные бренды