Majestic JADE32IN-B Скачать руководство пользователя страница 59

Страница: 59 / 76

Majestic • JADE32IN-B, JADE42IN-B, JADE42IL-B Installation Manual • 2619-986 Rev. B • 10/19

B. Non-Combustible Board and Drywall In-

stallation

Introduction

If the desired finished fireplace installation does not utilize

non-combustible finishing materials (such as tile, marble,

stone, etc.), special attention must be paid to the instal

lation of drywall/gypsum wallboard to minimize potential

development of cracking and paint discoloration. Hearth

and Home Technologies has tested the following methods

and materials and therefore recommends the following

steps for the best drywall performance.

Attaching Non-Combustible Board to Framing

1. To ensure the lower cover panel has been correctly

installed, verify that two screws (total) have been

installed in the lower left and right sides of the fire

place opening. See Figure 8.1. These screws, when

installed, will ensure the lower panel is correctly in

stalled. If the lower cover panel is not correctly in

stalled, the decorative barrier front may not fit into the

fireplace opening correctly. Refer to section 6.D for

more information regarding the included non-combus

tible board.

2. The appliance ships with the required non-combus

tible board. The large top piece of non-combustible

board is pre-installed at the factory. The narrow left

and right non-combustible pieces are shipped within

the appliance. Install the non-combustible side pieces

with the screws provided in the manual bag assembly.

There are pilot holes located on the left and right side

columns. Care should be taken not to tighten these

screws into the non-combustible board excessively.

Set screws flush to the face of the non-combustible

board. See Figure 10.2 and Section 6.D.

3. The outer perimeter of the factory-installed non-com

bustible board has pre-drilled pilot holes. See Figure

10.1. Secure the non-combustible board to adja

cent framing with drywall screws that are a minimum

of 1-1/4 inch in length. Care should be taken not to

tighten these screws into the non-combustible board

excessively. Set screws flush to the face of the non-

combustible board. See Figure 10.2 and Section 6.D.

4. When installing drywall around the appliance, install

a rectangular hole for the fireplace/non-combustible

board in a single sheet of drywall. This will minimize

the joints that require finishing adjacent to the fireplace

opening. Ensure that the 1/8 inch gap is maintained

between the factory installed non-combustible board

and the surrounding drywall. See Figure 10.1. Secure

the drywall to the framing with screws a minimum of

one inch in length every six inches across the top of

the fireplace and every ten inches on the sides of the

fireplace.

5. To ensure good adhesion of drywall compounds and

tape, thoroughly clean the non-combustible board and

surrounding drywall to remove dust. The non-com

bustible board may be primed with a high-quality PVA

primer.

PRE-DRILLED

PILOT HOLES

APPLIANCE

OPENING

FILL GAPS

Figure 10.1 Install Non-Combustible Board

Filling and Finishing Seams

Step 1:

Fill all gaps and joints between the non-

combustible board pieces and the drywall with a

general purpose chemically setting joint compound

such as Durabond® 45 Joint Compound manufactured

by USG (Sheetrock® brand), recommended by Hearth

& Home Technologies. Use a drywall knife to firmly

press the joint compound into all gaps. See Figure

10.1. Allow these joints to dry.

Step 2:

All joints are to be taped with fiberglass mesh

tape 1 7/8” minimum width, and embedded with

Setting-Type joint compound, such as with Durabond®

Joint Compound manufactured by USG (Sheetrock®

brand), or equivalent. Allow these joints to dry.

Step 3:

Depending on the technique used in steps

1 and 2, two to three finishing coats are required to

provide a smooth and durable finish. Hearth and

Home Technologies recommends a lightweight or all-

purpose compound. Allow each coat to properly cure.

Allow the finishing coat(s) to cure for 24 hours before

operating appliance.

Painting

If desired finishing includes a painted wall, a high-quality

100% acrylic latex paint with a high-quality latex primer

base coat are recommended around the appliance to limit

discoloration. Oil-based or standard acrylic paints may

be more prone to discoloration due to heat exposure.

Drywall Joint-Crack Prevention and Repair

Drywall joints around the fireplace will be affected by ex

posure to elevated temperatures, along with other envi

ronmental, structural factors due to new construction, and

methods used to install and finish the drywall. If a crack

does emerge adjacent to the fireplace, it can be perma

nently repaired by filling it with a paintable latex caulk,

followed by repainting.
Some movement of the screws used to secure the non-

combustible board to the appliance/surround framing is

expected. If a blemish begins to show over a screw head,

sand the surface to remove the blemish and repaint.

Содержание JADE32IN-B













































































Результаты поиска

Содержание JADE32IN-B

Отзывы:

Бренды по названию

Популярные бренды

Majestic JADE32IN-B, Руководство по установке

Результаты поиска

Содержание JADE32IN-B

Отзывы:

Бренды по названию

Популярные бренды