Majestic JADE32IN-B Скачать руководство пользователя страница 40

Страница: 40 / 76

Majestic • JADE32IN-B, JADE42IN-B, JADE42IL-B Installation Manual • 2619-986 Rev. B • 10/19

B. Prepare For Heat Management

Introduction

An optional heat management system allows the heat from

the appliance to be redirected as desired.
An optional heat management system must be installed by

a qualified service technician at the time of the appliance

installation. Follow the instructions shipped with the kit for

installation and operation.

NOTICE:

Additional clearances are required for heat

management systems installations. Provisions must be

made in advance to ensure fit within the framing.

• Determine the heat management system(s) that will be

installed.

• Locate the two heat management ports on the top of the

appliance. Either one or two Heat-Zone

-Gas Kits may

be installed.

See Figure 6.2. Remove the knockouts

from the appliance with a tin snips.

• Center the duct collar or passive heat adapter around

the exposed hole and attach it to the appliance. See

Figure 6.5.

Note

: Do this BEFORE final positioning of the appliance.

• Determine the location for the air register/fan housing

assembly.

Reference the Heat-Zone

-Gas Kit, Smart-Wall™ TV

Kit, Heat-Duct Kit, Heat-Out-Gas Kit or Passive Heat

instructions for the remaining installation steps.

Heat Management System options are:

•

HEAT-ZONE

GAS: The heat is diverted into an

adjacent room.

• HEAT-OUT-GAS: The heat is diverted outside the

home/building.

•

Smart-Wall™ TV Kit: The warm air from the appliance

is conveyed through an air duct to remote locations in

the same room or other rooms of the building.

• Passive Heat (PH-FRT, PH-SIDE): The heat is vented

into the room in which the appliance is installed

through a discharge opening(s).

WARNING! Risk of Fire!

DO NOT block passive heat

registers! Overheating of appliance and combustible

materials will occur.

The JADE32IN-B, JADE42IN-B and JADE42IL-B models

may utilize two Heat Management Systems, but not all

are compatible.
The HEAT-OUT-GAS kit may be used with either HEAT-

ZONE

-GAS or one of the Passive Heat options.

Passive Heat may be used with HEAT-OUT-GAS or

one

HEAT-ZONE

GAS. The dedicated knockouts, as

shown in Figure 6.5, must be used only as indicated.

Passive Heat cannot be used with the Smart-Wall TV Kit

or optional fan.

Smart-Wall™ TV Kit

When a Smart-Wall™ TV Kit is installed, only one Heat-

Zone

-Gas kit or one Heat-Out-Gas kit may be installed.

The

Smart-Wall™ TV Kit can not be used with a power

vent option or optional fan.

Figure 6.5 Proper Positioning, Leveling And Securing Of

Appliance

WARNING! Risk of Fire!

DO NOT remove a knockout

unless a heat management system will be installed in its

place. Appliance and combustible materials will overheat.

REMOVE KNOCKOUTS

Содержание JADE32IN-B













































































Результаты поиска

Содержание JADE32IN-B

Отзывы:

Бренды по названию

Популярные бренды

Majestic JADE32IN-B, Руководство по установке

Результаты поиска

Содержание JADE32IN-B

Отзывы:

Бренды по названию

Популярные бренды