manualshive.com logo in svg

Majestic Chateau DVT38, Инструкции по установке и руководство для владельца

Поделиться
Скачать
Majestic Chateau DVT38 Скачать руководство пользователя страница 2

2

Vermont Castings, Majestic Products Chateau™

20006081

Please read the installation & operating instructions before using this appliance.

Thank you and congratulations on your purchase of a Vermont Castings, Majestic Products fireplace.

IMPORTANT:  Read all instructions and warnings carefully before starting installation.

Failure to follow these instructions may result in a possible fire hazard and will void the warranty.

Table of Contents

Installation & Operating Instructions

Important Curing/Burning Instructions ................................................................................ 3
Locating Your Fireplace ..................................................................................................... 3
Fireplace Dimensions ......................................................................................................... 4
Clearance to Combustibles ................................................................................................ 5
Mantels .............................................................................................................................. 5
Hearth .............................................................................................................................. 5
Framing & Finishing ........................................................................................................... 6
Final Finishing .................................................................................................................... 7
Gas Specifications ............................................................................................................. 7
Gas Inlet and Manifold Pressures ...................................................................................... 7
High Elevations .................................................................................................................. 7
Gas Line Installation ........................................................................................................... 7
Remote ON/OFF Switch .................................................................................................... 8
Electrical Junction Box ....................................................................................................... 8
Electronic Gas Control Valve ............................................................................................. 8

General Venting Information

General Venting ................................................................................................................. 9
General Venting Information - Termination Location ....................................................... 10
General Information Assembling Vent Pipes ................................................................... 11
SK8 Venting Pipes ........................................................................................................... 11
Horizontal Termination ..................................................................................................... 12
Vertical Termination ......................................................................................................... 12
Sidewall Applications ....................................................................................................... 12
Use of the Restrictor Plates in Horizontal Venting Applications ....................................... 12
Sidewall Installation .......................................................................................................... 14
Vertical Through-the-Roof Applications ........................................................................... 15
Use of Restrictor Plates for Vertical Venting Applications ................................................ 15
Vertical Through-the-Roof Installation .............................................................................. 17
Chimney Components ...................................................................................................... 19

Operating Instructions

Glass Information ............................................................................................................. 20
Window Frame Assembly Removal ................................................................................. 20
Glass Cleaning ................................................................................................................. 20
Restrictor Plate Installation .............................................................................................. 20
Ceramic Refractory Installation ........................................................................................ 21
Log, Lava Rock and Ember Placement ............................................................................ 22
Flame & Temperature Adjustment ................................................................................... 24
Flame Characteristics ...................................................................................................... 24
Lighting and Operating Instructions (Standing Pilot Models) ........................................... 25
Lighting and Operating Instructions (Electronic Ignition Models) ..................................... 26
Troubleshooting ............................................................................................................... 27
Fuel Conversion ............................................................................................................... 29

Maintenance

Cleaning the Standing Pilot Control System .................................................................... 32
Cleaning Electronic Ignition System ................................................................................. 32
Battery Replacement for Ignitor Module ........................................................................... 32

Replacement Parts ....................................................................................................................... 33
Optional Accessories .................................................................................................................. 36
Warranty ....................................................................................................................................... 37

Содержание Chateau DVT38







































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды